Melting, boiling and evaporation · Physics Class 9–10 | StemPy Lab
Course 10.2·Lesson 3 of 3
Melting, boiling and evaporation
Heat ice steadily and the temperature rises, stops at 0 degrees Celsius while the ice melts, and rises again. Boiling is the same at 100 degrees Celsius. In a changing state the energy goes into the particles' arrangement, not into their speed. Evaporation is different: it happens at any temperature, at the surface, and it cools.
about 30 min1 simulation2 practice questions
Lesson 3 of 3Show all lessonsHide
Try the code and the simulations beside the lesson.
A thermometer in a pan of ice
Put a thermometer in crushed ice and heat it with a steady flame. The temperature rises to 0∘C and then stops rising. The ice is still being heated, but the temperature stays at 0∘C until all the ice has gone. Only then does it rise again. The same thing happens at 100∘C as the water boils. Where does the energy go?
Melting and boiling
While a solid melts, or a liquid boils, we keep giving it energy, but the temperature stays the same. The energy does not make the particles move faster. It is used to change the arrangement of the particles. In melting, the energy frees the particles from their fixed places. In boiling, the energy lets them move far apart.
For pure water at standard atmospheric pressure (the normal pressure of the air at sea level):
The melting point is 0∘C.
The boiling point is 100∘C.
A graph of temperature in degrees Celsius against time in seconds for 0.50 kilograms of ice, heated steadily from minus 20 degrees to above 100 degrees. The line rises steeply from A to B and then is flat at 0 degrees from B to C while the ice melts. It rises again from C to D, more gently, to 100 degrees. It is flat at 100 degrees from D to E while the water boils. The flat parts are labelled melting and boiling.
Reading the heating curve of ice from left to right:
AB. The ice warms from −20∘C to 0∘C. The particles vibrate more.
BC. The ice melts at 0∘C. The graph is flat. Solid and liquid are both present.
CD. The water warms from 0∘C to 100∘C.
DE. The water boils at 100∘C. The graph is flat. Liquid and gas are both present.
The heater here gives the same energy every second, so the time of each part tells us how much energy that part needs. The time for AB is 21 s, for BC 167 s, for CD 210 s and for DE 1130 s. Boiling takes by far the most energy, because the particles must be separated completely. The energy that melts or boils 1 kg of a substance is called a latent heat. You do not need it for this course. It comes in the Class 11-12 chapter on thermal properties of matter. For the exam you only need the shape of the curve.
A worked example. A heater of power 1500 W is left on for 240 s while a pan of water boils. How much energy does it transfer?
The rule. Energy = power × time, so E=Pt.
The energy.E=1500W×240s=360000J=360kJ.
The meaning. This energy changes the water to steam. The temperature stays at 100∘C.
Condensation and solidification
These are the reverse changes.
Condensation: gas to liquid. The particles of a gas lose energy and slow down. The forces between them pull them together, and they form a liquid.
Solidification (freezing): liquid to solid. The particles of a liquid lose energy and slow down until they settle into fixed places in a pattern.
Evaporation
The Chemistry chapter Matter in Our Surroundings looks at the same changes of state and adds humidity and drying in daily life. A puddle dries on a warm day without ever boiling. A liquid can turn into a gas at a temperature far below its boiling point. This is evaporation.
The particles of a liquid do not all move at the same speed. Some are faster than the average. A fast particle at the surface may have enough energy to escape from the liquid into the air above.
A beaker of liquid drawn as a box of particles. Near the surface two fast particles, shown with long arrows, leave the liquid and move into the air above. The other particles stay in the liquid and move more slowly, shown with short arrows.
When the faster particles leave, the particles that remain have a lower average speed. So their kinetic energy goes down, and the liquid cools. That is why wet skin feels cold, and why sweat cools us.
Extended: boiling and evaporation are different in several ways.
Boiling: only at the boiling point, throughout the liquid, with bubbles. It is fast.
Evaporation: at any temperature, only at the surface. It is slow.
Extended: evaporation is faster when:
the temperature of the liquid is higher, so more particles have enough energy to escape;
the surface area is bigger, so more particles are at the surface;
air moves over the surface, because wind carries away the escaped particles, and fewer return to the liquid.
Extended: an object in contact with an evaporating liquid is cooled. Think of a wet cloth around a bottle. The liquid takes the energy it needs to evaporate from the bottle. The bottle loses energy, so its temperature falls.
Practise with new numbers
Try it in Python
The program follows 0.50kg of ice, heated by a 1000W heater, through its four stages. It prints the time at which each stage ends.
Common mistakes
Saying that the temperature rises while a solid melts. It stays the same, at the melting point.
Saying that the energy is wasted during melting. The energy is used to change the arrangement of the particles.
Mixing up boiling and evaporation. Boiling happens throughout the liquid at one temperature. Evaporation happens at the surface at any temperature.
Thinking that evaporation warms the liquid. It cools it, because the fastest particles leave.
Forgetting the conditions. The melting and boiling points of water, 0∘C and 100∘C, are for standard atmospheric pressure.
Remember these
During melting and boiling, energy goes in and the temperature stays the same.
Water melts at 0∘C and boils at 100∘C at standard atmospheric pressure.
Condensation: gas to liquid. Solidification: liquid to solid. The particles lose energy and slow down.
Evaporation: the more energetic particles escape from the surface, and the liquid cools.
Extended: boiling is at one temperature, throughout the liquid, with bubbles. Evaporation is at any temperature, at the surface. A higher temperature, a bigger surface and moving air speed it up.
Check yourself
Try each one on your own first. If you are stuck, open a hint. Then check with Show the answer.
Ice at 0∘C is heated and melts. Why does the temperature not rise while it melts?
A heater of power 800 W is on for 180 s. How much energy does it transfer?
Why does a liquid cool when it evaporates?
Extended. Give two differences between boiling and evaporation.