How do you know the exact moment an acid has just neutralised an alkali? You use a burette, a pipette and an indicator. This lesson describes the method, the end-point, and how the results give the concentration of the alkali.
about 30 min1 simulation2 practice questions
Lesson 3 of 3Show all lessonsHide
Try the code and the simulations beside the lesson.
What a titration does
A titration finds how much of one solution just reacts with a measured volume of another. In an acid-base titration, a solution of known concentration is added from a burette to a fixed volume of the other solution until the reaction is complete. You met the idea in the Class 9-10 chapter on Acids and Bases. Here we do the full method.
The apparatus is shown below.
A burette holds the acid of known concentration.
A volumetric pipette with a pipette filler measures 25.0cm3 of alkali into a conical flask.
A few drops of a suitable indicator go into the flask.
A white tile under the flask makes the colour change easy to see.
A small funnel helps to fill the burette.
A drawing of a titration. A burette clamped to a stand holds acid of known concentration, with a tap at the bottom. Under its tip a conical flask stands on a white tile. The flask holds 25.0 cm3 of alkali from a volumetric pipette, with a few drops of indicator. A curved arrow shows the flask being swirled. Labels name the burette, the tap, the conical flask, the white tile and the swirling.
The method
Rinse the burette with a little of the acid. Fill it, using the funnel, and then take the funnel away. Run a little acid through the tap so that the tip is full. Read the start, at the bottom of the curve.
Use the pipette and filler to put 25.0cm3 of alkali into the flask. Add two or three drops of indicator.
Stand the flask on the white tile under the burette.
Run the acid into the flask and swirl all the time. Do a quick rough titration first. It shows roughly where the colour changes.
Repeat, adding the acid fast at first and then drop by drop near the rough value.
Stop when the indicator changes colour and stays changed. This is the end-point. Read the burette.
The titre is the end reading minus the start reading. Repeat until two titres agree within 0.20cm3. They are concordant. Use the mean of the concordant titres and leave out the rough one.
The indicator and the end-point
A suitable indicator changes colour sharply at the end-point. Two indicators in the syllabus are methyl orange, which changes at pH 3.1 to 4.4, and thymolphthalein, which changes at pH 9.3 to 10.5.
Indicator
In acid
In alkali
methyl orange
red
yellow
thymolphthalein
colourless
blue
Look at the graph. It shows the pH when 0.100mol/dm3 hydrochloric acid is added to 25.0cm3 of 0.100mol/dm3 sodium hydroxide solution. Near 25.0cm3 the pH falls almost vertically. Between 24.95cm3 and 25.05cm3, only a drop or two, it falls from 10.0 to 4.0. Both indicator ranges lie on that steep part, so one drop of acid changes the colour.
A graph of pH against the volume of 0.100 mol/dm3 hydrochloric acid added to 25.0 cm3 of 0.100 mol/dm3 sodium hydroxide solution. The pH starts at 13 and falls slowly. At 25.0 cm3 it drops almost vertically from about 10 to about 4 and then falls slowly to about 1.6. A grey band at pH 9.3 to 10.5 marks where thymolphthalein changes colour. A second band at pH 3.1 to 4.4 marks methyl orange. Both bands lie on the steep part of the curve, at the end-point of 25.0 cm3.
Alkali in the flask with thymolphthalein is blue. At the end-point it turns colourless. With methyl orange, the yellow solution turns orange and then red. Universal indicator changes through many colours gradually, so it cannot show one sharp end-point.
Extended: working out the concentration
The syllabus asks Extended candidates to use titration data to find moles or a concentration. The steps are always the same.
Find the moles of the solution you know: moles=concentration (mol/dm3)×1000volume (cm3).
Use the equation to find the moles of the other substance.
Divide those moles by the volume of the other solution in dm3.
Example 1.25.0cm3 of sodium hydroxide needs 22.40cm3 of 0.100mol/dm3 hydrochloric acid. HCl+NaOH→NaCl+H2O is one to one.
Moles of HCl: 0.100×100022.40=0.002240mol.
Moles of NaOH: also 0.002240mol.
Concentration: 0.02500.002240=0.0896mol/dm3.
In grams per dm3: 0.0896×40=3.58g/dm3, because Mr of NaOH is 40.
Example 2. The equation H2SO4+2NaOH→Na2SO4+2H2O is one to two. The moles of NaOH are twice the moles of H2SO4. Always read the ratio from the equation.
A bigger titre means more acid was needed, so the alkali is more concentrated.
Practise with new numbers
Try it in Python
The program takes the rough titration out, finds the mean of two concordant titres, and works out the concentration.
Common mistakes
Forgetting to divide by 1000. A volume in cm3 must become dm3 before you multiply by a concentration in mol/dm3.
Ignoring the ratio. Read it from the equation. Sulfuric acid needs two moles of sodium hydroxide.
Including the rough titre in the mean. Use only the concordant titres.
Adding the acid too fast near the end-point. One extra drop can pass the colour change.
Filling the burette without clearing the tip. An air bubble leaves during the titration and makes the titre too big.
Dividing by the titre, not by the volume of alkali. The concentration of the alkali uses the 25.0cm3 in the flask.
Remember these
A titration uses a burette, a volumetric pipette and a suitable indicator.
The end-point is where the indicator just changes colour and stays changed.
Repeat until two titres agree within 0.20cm3. Use their mean.
Methyl orange: red in acid, yellow in alkali. Thymolphthalein: colourless in acid, blue in alkali.
Extended: moles of known solution, then the equation ratio, then divide by the volume in dm3.
Check yourself
Try each one on your own first. If you are stuck, open a hint. Then check with Show the answer.
Why is the conical flask swirled while the acid is added?
Why is the first titration called a rough titration, and why is it left out of the mean?
Which indicator in this lesson is red in acid and yellow in alkali?
Extended: 25.0cm3 of potassium hydroxide needs 16.50cm3 of 0.200mol/dm3 hydrochloric acid. Find the concentration of the alkali. HCl+KOH→KCl+H2O.
Extended: How many moles of sodium hydroxide react with 0.0030mol of sulfuric acid?
References
Cambridge IGCSE Chemistry 0620 syllabus for 2026 to 2028, section 12.2 (Acid-base titrations), Core 1 and 2, and section 3.3 (the mole), Supplement 5, 6 and 8.
OpenStax, Chemistry 2e, Chapter 4, section 4.5 (Quantitative Chemical Analysis), for titration.
Enroll free in Experimental Design and Acid-Base Titrations
Every lesson is open to read. Enrolling also lets you:
Mark lessons done and carry on where you stopped.
Take the tests of this lesson and its course.
Count the course towards the certificate for its chapter.