Electroplating with electrolysis · Chemistry Class 9–10 | StemPy Lab
Course 10.1·Lesson 3 of 3
Electroplating with electrolysis
Cutlery, taps, car trim and food cans often have a thin layer of another metal on top. The layer is put there by electrolysis. We see why metal objects are plated, and exactly how it is done.
about 30 min1 simulation2 practice questions
Lesson 3 of 3Show all lessonsHide
Try the code and the simulations beside the lesson.
Why plate a metal object?
Electroplating puts a thin layer of one metal on top of another metal object, using electrolysis. Metal objects are electroplated for two reasons:
To improve their appearance. Silver plating on cutlery and chromium plating on a car bumper make a bright, shiny surface.
To improve their resistance to corrosion. The layer keeps oxygen and water away from the metal below. Steel food cans are plated with tin, and steel taps with chromium.
The layer must be thin. A thick layer would cost too much of the plating metal.
How a spoon is silver plated
Look at the picture. These three rules work for every plating job:
The object to be plated is the cathode (negative). It is joined to the negative terminal.
The anode is a bar of the plating metal. For silver plating, it is a bar of silver.
The electrolyte is a solution that contains ions of the plating metal. For silver plating, it is silver nitrate solution.
A drawing of silver plating. A beaker holds silver nitrate solution. A silver bar is joined to the positive terminal of the battery and is the anode. A spoon is joined to the negative terminal and is the cathode. Silver ions move through the solution from the bar to the spoon. A thin grey coat grows on the spoon. Half-equations: at the anode Ag gives Ag+ plus e-, at the cathode Ag+ plus e- gives Ag.
What happens when the current flows:
Silver ions in the solution move to the spoon. At the cathode each one gains an electron and becomes a silver atom on the surface: Ag++e−→Ag. The spoon gets a layer of silver.
At the anode a silver atom loses an electron and dissolves as an ion: Ag→Ag++e−. The silver bar gets smaller.
The silver ions that leave the solution at the cathode are replaced by the silver that dissolves at the anode. So the colour and the concentration of the solution stay almost the same, and the process can run for a long time. The Extended half-equations are the two equations above.
Good plating
A good coat is smooth, even and strong. These steps help:
Clean the object first, with a solvent and then with acid. Grease and dirt stop the metal from sticking.
Use a small, steady current. A large current makes a rough, loose layer.
Turn the object or use more than one anode, so that every side is coated.
The mass of the coat depends on the charge that passes, so more time or more current gives a thicker coat. Each mole of electrons deposits one mole of silver, or half a mole of copper or nickel.
Silver, Ag+: 1 electron for each atom, so one mole of electrons deposits 108g.
Copper, Cu2+: 2 electrons for each atom, so one mole of electrons deposits 32g.
Nickel, Ni2+: 2 electrons for each atom, so one mole of electrons deposits 29.5g.
Copper plating uses a copper anode and copper(II) sulfate solution. Nickel plating uses a nickel anode and nickel sulfate solution. The same three rules apply.
Practise with new numbers
Try it in Python
The program finds the mass of silver and the thickness of the coat on a spoon.
Common mistakes
Putting the object at the anode. The object that is plated must be the cathode, because metal ions gain electrons there.
Using the wrong electrolyte. It must contain ions of the plating metal, such as silver nitrate for silver.
Using an inert anode. The usual anode is the plating metal itself, and it dissolves to replace the ions that are used.
Forgetting to clean the object. A dirty surface gives a patchy coat.
Thinking that the coat is paint. The metal is deposited atom by atom, so it is a layer of real metal.
Remember these
Objects are electroplated to improve their appearance and to resist corrosion.
The object is the cathode. The anode is the plating metal. The electrolyte has ions of the plating metal.
Extended: cathode Ag++e−→Ag, anode Ag→Ag++e−.
Clean the object first and use a small, steady current.
Mass deposited depends on the moles of electrons and on the charge of the ion.
Check yourself
Try each one on your own first. If you are stuck, open a hint. Then check with Show the answer.
Name the three things needed to nickel plate an iron key.
Why does a tin layer on a steel can protect the steel?
During silver plating, what happens to the mass of the silver anode?
Why is the object cleaned before it is plated?
0.060 mol of electrons pass in a copper plating cell. What mass of copper is deposited? Ar of copper is 64.
References
Cambridge IGCSE Chemistry 0620 syllabus for 2026 to 2028, section 4.1 (Electrolysis), Core 6 and 7.