Course 35.2Lesson 3 of 3
Iron is made with coke, zinc with coke at a much higher temperature, chromium with aluminium, and aluminium with electricity. Each choice can be read from the Ellingham diagram. This lesson works through the blast furnace equilibria, zinc, copper, chromium, titanium and aluminium, and explains why sulphides are roasted first.
Try the code and the simulations beside the lesson.
The iron oxides do not lose their oxygen in one step. Haematite goes to magnetite, magnetite to iron(II) oxide, and iron(II) oxide to iron. The first two steps are easy: their oxide lines lie high, and carbon monoxide reduces them in the cooler upper part of the furnace, at 500 to 800 K.
and
The last step is the hard one. From the lines, for one mole of iron(II) oxide,
Near 1200 K this is slightly positive, so is below 1. Carbon monoxide still reduces iron(II) oxide, but only if the gas is rich in carbon monoxide, about three parts in four.
Who keeps the gas so rich? Hot coke. Carbon dioxide that touches coke is turned back into carbon monoxide:
This Boudouard reaction has near 983 K and is strongly favoured above it. In the hot zone, 900 to 1500 K, the gas over the coke is almost all carbon monoxide, and iron(II) oxide is reduced. In effect carbon is the reducing agent there:
Slide from 900 K to 1200 K. Near 1000 K the blue curve passes above the orange one, and from there the gas over coke can reduce iron(II) oxide.
The zinc line meets the carbon line near 1263 K (with the straight line; the kink at the boiling point moves it a little lower, near 1235 K). So zinc oxide is reduced by coke only at a high temperature, and the plant works near 1673 K:
At this temperature zinc comes off as a vapour. It is led away and cooled quickly. If it cooled slowly in contact with carbon dioxide, it would be oxidised back. The NCERT book prints 673 K for this step. That temperature is far too low by the diagram; real retorts run above 1373 K.
The copper(I) oxide line lies high, above the carbon line at every furnace temperature. So carbon reduces copper(I) oxide easily. But copper ores are sulphides, and there is a neater route. Partly roast the sulphide, and let the oxide react with the sulphide left:
This self-reduction has a positive but a large positive , because a gas is made. Above about 860 K it goes downhill.
Why not reduce a sulphide with carbon directly? The product would be carbon disulphide:
Carbon disulphide has a positive Gibbs energy of formation, so carbon is a very poor taker of sulphur, and hydrogen sulphide is only a little better. There is no low line on a sulphide diagram that carbon can use. Oxides, on the other hand, sit above the falling carbon line at high temperature. So a sulphide is first roasted to the oxide.
The chromium(III) oxide line meets the carbon line near 1489 K, and chromium also forms carbides. So chromium is made by the thermite process, with aluminium powder:
The aluminium line lies far below the chromium line at every temperature, and the reaction releases so much heat that the chromium melts. Welders use the same reaction with iron(III) oxide to join rails.
Titanium. The titanium(IV) oxide line meets the carbon line only near 1990 K, and titanium carbide forms anyway. So the oxide is first turned into the chloride with chlorine and carbon, and the chloride is reduced by magnesium. This is the Kroll process:
, then
Aluminium. The aluminium line is so low that carbon reduces alumina only above about 2300 K. Magnesium could do it, but magnesium is made by electrolysis itself. So aluminium is won by electrolysis of molten alumina, as course 3 shows.
The program works out the two equilibria of the blast furnace at one temperature.
Try each one on your own first. If you are stuck, open a hint. Then check with Show the answer.
Every lesson is open to read. Enrolling also lets you:
Log in to join the discussion.
Loading…
This lesson is free to read. Enroll free to keep your place and take the tests.