Concentrating an ore: washing, magnets, froth and leaching
A ton of copper ore may hold only a few kilograms of copper. Before anything is heated, the gangue must go. This lesson explains four ways to concentrate an ore: hydraulic washing, magnetic separation, froth flotation and leaching, with the Bayer and cyanide processes.
about 25 min1 simulation1 practice question
Lesson 2 of 3Show all lessonsHide
Try the code and the simulations beside the lesson.
Why concentrate first?
Heating a whole mountain of rock to get a little metal wastes fuel and furnace space. So we first remove most of the gangue. The method depends on a difference between the mineral and the gangue: density, magnetism, how the surface takes up oil, or how the mineral dissolves. Concentration is also called dressing or benefaction of the ore.
Hydraulic washing
This is gravity separation. Powdered ore is washed by an upward stream of running water. The lighter gangue is carried away, and the heavier mineral stays behind. It works when the ore is much denser than the gangue, as for the oxide ores of tin and for gold in sand.
Magnetic separation
If either the mineral or the gangue is attracted by a magnet, a magnetic roller separates them. Magnetite, chromite and pyrolusite are attracted. Tin stone (cassiterite, SnO2) is not magnetic, but the wolframite mixed with it is, so the magnet removes the wolframite.
Magnetic separation. Powdered ore falls from a hopper onto a belt that runs over two rollers. The right roller is a magnet. The non-magnetic gangue flies off the end of the belt and lands in a near heap. The magnetic particles stick to the belt a little longer and drop in a second heap, under the roller, labelled magnetic mineral.
Froth flotation
This method is used mainly for sulphide ores. The powdered ore is mixed with water to a thin mud called the pulp. Two kinds of reagent are added.
Collectors, such as pine oil, fatty acids and xanthates, make the surface of the sulphide water-repellent. The mineral then sticks to air bubbles.
Froth stabilisers, such as cresols and aniline, keep the froth from breaking.
A stirrer beats air into the pulp. The bubbles carry the sulphide particles to the top, where a froth forms and is skimmed off. The gangue is wetted by the water and sinks.
A froth flotation cell drawn in section. A tank holds a grey pulp of powdered ore, water and oil. A stirrer in the middle beats air in through a pipe at the bottom, and air bubbles rise. Dark sulphide particles stick to the bubbles and collect in a froth on top, which flows over the lip into a launder labelled froth with the mineral. Pale gangue particles sink and leave at the bottom, labelled gangue with water.
Depressants let us separate two sulphides. For an ore of galena, PbS, with zinc blende, ZnS, sodium cyanide is added. It forms a zinc cyanide complex on the surface of the zinc blende, so the zinc blende does not float. Galena comes up with the froth first. Later the zinc blende can be activated and floated.
A flotation balance. Plants judge flotation by two numbers. Let f, c and t be the percentages of metal in the feed, the concentrate and the tailings (the rejected part). Mass and metal are both conserved. From these two balances,
mass of concentrate=feed×c−tf−t
R=f(c−t)c(f−t)
where R is the recovery, the share of the metal that reaches the concentrate.
Set f=1.5%, c=24% and move t. Each extra 0.05 % of copper left in the tailings costs a few percent of the recovery, because the tailings are almost all of the mass.
Leaching
In leaching the mineral dissolves in a suitable reagent and the gangue does not.
The Bayer process for bauxite. Bauxite holds silica, iron oxides and titanium oxide as impurities. It is digested with a concentrated solution of sodium hydroxide at 473 to 523 K under pressure. Alumina dissolves as sodium aluminate. Iron oxide does not dissolve, and it is filtered off as a red mud.
Al2O3(s)+2NaOH(aq)+3H2O(l)→2Na[Al(OH)4](aq)
The solution is then neutralised by passing in carbon dioxide, and seeded with a little freshly prepared hydrated alumina. Hydrated alumina comes out.
Silica stays in the solution as sodium silicate. The hydrated alumina is filtered, dried and heated to about 1470 K to give pure alumina.
Al2O3⋅xH2O(s)→Al2O3(s)+xH2O(g)
The cyanide process for gold and silver. The ore is leached with dilute sodium cyanide solution in the presence of air. Oxygen oxidises the metal, and cyanide holds it in solution as a complex.
4M(s)+8CN−(aq)+2H2O(l)+O2(g)→4[M(CN)2]−(aq)+4OH−(aq) with M = Ag or Au
Zinc, a more reactive metal, then displaces the gold or silver.
2[M(CN)2]−(aq)+Zn(s)→[Zn(CN)4]2−(aq)+2M(s)
Low-grade copper ores and copper scrap are leached with acid or with bacteria. The solution of copper(II) ions is then treated with scrap iron or hydrogen, which gives copper. This route is called hydrometallurgy.
Practise with new numbers
Try it in Python
The program works out the mass of concentrate and the recovery of a flotation circuit.
Common mistakes
Using froth flotation for an oxide ore. It suits sulphides, whose surfaces take up the collector.
Mixing up the reagents. Pine oil and xanthates collect. Cresols and aniline stabilise the froth. Sodium cyanide depresses zinc blende.
Forgetting the air in the cyanide process. Oxygen is the oxidising agent. Without it the gold does not dissolve.
Thinking iron oxide dissolves in the Bayer process. It stays behind as red mud. Silica dissolves.