Course 35.3Lesson 2 of 3
A metal from the furnace is never pure. Copper for wires must be more than 99.9 % copper, and silicon for chips must be purer still. How is that done? This lesson sets out the methods of refining and the property of the metal that each one uses.
Try the code and the simulations beside the lesson.
The crude metal carries other metals, carbon, sulphur and oxides. A little impurity changes a metal a lot. For example, a trace of arsenic makes copper conduct much worse. Each refining method uses a difference between the metal and its impurities.
Metals with a low boiling point, such as zinc (1180 K) and mercury (630 K), are boiled off and condensed. The impurities stay behind.
A metal with a low melting point, such as tin, is heated on a sloping hearth. The metal melts and flows down. The impurities that melt at a higher temperature stay on the hearth.
Molten blister copper still holds some copper(I) oxide. It is stirred with logs of green wood. The gases and hydrocarbons from the wood reduce the oxide to copper.
The impure metal is the anode. A thin strip of pure metal is the cathode. The electrolyte is a solution of a salt of the metal. For copper, it is copper(II) sulphate acidified with sulphuric acid.
At the anode: . At the cathode: .
So copper only moves from the anode to the cathode, and the cell voltage is small, about 0.2 to 0.4 V.
Zinc is refined in the same way, with zinc sulphate as the electrolyte.
This method gives metals of very high purity, as needed for semiconductors: silicon, germanium, boron, gallium and indium. It rests on one fact: impurities are more soluble in the melt than in the solid.
A ring heater melts a narrow zone of a bar and moves slowly along it. Pure metal freezes behind the zone. The impurities stay in the molten zone and are swept to one end, which is cut off. The pass is repeated many times.
The distribution coefficient is the ratio of impurity in the freezing solid to that in the melt. After one pass, at a distance along a bar, with a zone of length ,
where is the impurity before the pass.
Set . The start of the bar keeps only a fifth of its impurity after one pass. Then set . The cleaning is much weaker. Plants with a large simply repeat the pass many times.
The metal is turned into a volatile compound, which is collected and then broken down to give the pure metal.
The Mond process for nickel. Crude nickel is heated in a stream of carbon monoxide at 330 to 350 K. Volatile nickel tetracarbonyl forms, and the impurities stay solid.
at 330 to 350 K
The carbonyl vapour is heated to 450 to 470 K, where it breaks up into pure nickel and carbon monoxide, which is used again.
at 450 to 470 K
The van Arkel method for zirconium and titanium. It removes oxygen and nitrogen, which spoil these metals. The crude metal is heated with iodine in an evacuated vessel. The volatile iodide forms:
The iodide vapour meets a tungsten filament heated electrically to about 1800 K. It breaks up, and pure metal is deposited on the filament.
A mixture is put on a column of an adsorbent, such as alumina. A liquid moves through the column. The parts of the mixture are held back to different extents, so they come out at different times. Column chromatography purifies elements that are available only in small amounts, and elements whose impurities are very like them in chemistry.
The program works out the copper plated in a refining cell in a day, the silver that collects in the anode mud, and the energy used.
Try each one on your own first. If you are stuck, open a hint. Then check with Show the answer.
Every lesson is open to read. Enrolling also lets you:
Log in to join the discussion.
Loading…
This lesson is free to read. Enroll free to keep your place and take the tests.