Freundlich's rule fits readings, but why does a surface fill up? In 1916 Irving Langmuir pictured a surface with a fixed number of sites, each holding one molecule. From that picture he derived an isotherm. This lesson derives it, puts it in a straight-line form, and uses it to find the area of a powder.
about 25 min1 simulation1 practice question
Lesson 3 of 3Show all lessonsHide
Try the code and the simulations beside the lesson.
Langmuir's picture of a surface
Langmuir made four assumptions.
The surface has a fixed number of identical sites.
Each site holds at most one molecule, so only a monolayer forms.
All sites are equal, and a molecule on one site does not affect its neighbours.
At equilibrium, molecules are adsorbed and desorbed at the same rate.
Let θ (theta) be the fraction of the sites covered. Then 1−θ is the fraction still empty.
Deriving the Langmuir isotherm
Step 1. The rate of adsorption. A molecule can stick only where a site is empty. The number of molecules that hit the surface each second is proportional to the pressure P. So the rate of adsorption is
ra=kaP(1−θ)
Step 2. The rate of desorption. Only an occupied site can lose a molecule. So
rd=kdθ
Step 3. Equilibrium. The two rates are equal:
kaP(1−θ)=kdθ
Step 4. Solve for θ. Let K=ka/kd, the Langmuir constant. Then KP(1−θ)=θ, so KP=θ(1+KP), and
θ=1+KPKP
The amount adsorbed is proportional to θ. If V is the volume of gas held by one gram, and Vm is the volume for a full monolayer, then V=Vmθ:
V=1+KPVmKP
The older NCERT book writes the same result as mx=1+bPaP, with b=K and a=(x/m)maxK.
The two ends of the isotherm
Low pressure, KP≪1: θ≈KP. The amount is proportional to the pressure, like Freundlich with 1/n=1.
High pressure, KP≫1: θ≈1. The surface is full, like Freundlich with 1/n=0.
At P=1/K, exactly half the surface is covered.
So the Freundlich isotherm, with 1/n between 0 and 1, describes the middle stretch of a Langmuir curve.
Two graphs of the Langmuir isotherm. Left: the fraction of the surface covered, theta, against the pressure. It rises in a straight line at low pressure, bends, and levels off at 1 at high pressure, where a dashed line marks the full monolayer. Right: P divided by V against P for the same gas is a straight line with a positive intercept; the slope is 1 over the monolayer volume.
Set K=0.05kPa−1. The point at 20kPa shows half cover. Now double K: half cover comes at 10kPa. A larger K means a stronger hold on the surface.
The straight-line form
Turn the isotherm upside down and multiply by P:
VP=KVm1+VmP
Plot P/V against P. The line has slope 1/Vm and intercept 1/(KVm). So
Vm=1/slope,
K=slope/intercept.
From the monolayer to the surface area
Once we know Vm, we can count the molecules in one layer. Suppose Vm is measured at 273K and 1atm, where one mole fills 22400mL:
N=22400mL/molVm×NA
If each molecule covers an area σ (sigma), the surface area is A=Nσ. For nitrogen, σ=0.162nm2. This is how the area of catalysts and powders is measured in industry.
In practice the measurement uses nitrogen at 77K, where several layers can form. Brunauer, Emmett and Teller extended Langmuir's idea to many layers. Their BET isotherm gives Vm from such readings. You only need the idea: it is a multilayer form of the Langmuir picture.
Two more cases for olympiad work
Dissociative adsorption. Hydrogen on many metals splits into two atoms, and each atom takes a site. Now the rate of adsorption needs two empty sites, ra=kaP(1−θ)2, and desorption needs two filled ones, rd=kdθ2. Equating and taking the square root gives
θ=1+KPKP
At low pressure, θ≈KP, so the coverage grows as P1/2.
Two gases on one surface. If gases A and B compete for the same sites,
θA=1+KAPA+KBPBKAPA
A gas with a large K crowds the other off the surface. The next course uses this to explain catalyst poisons.
The enthalpy of adsorption from two isotherms
The constant K falls as the temperature rises, as for any exothermic equilibrium: K=K0e−ΔHads/RT. To keep the same coverage θ at two temperatures, K1P1=K2P2. Taking logarithms,
lnP1P2=−RΔHads(T11−T21)
This ΔHads is the isosteric enthalpy of adsorption ("isosteric" means at the same coverage). A higher temperature needs a higher pressure for the same coverage.
Practise with new numbers
Try it in Python
The program fits P/V against P for five readings, finds Vm and K, and works out the coverage at a new pressure.
Common mistakes
Forgetting the empty sites. The rate of adsorption depends on 1−θ, not on 1.
Mixing up slope and intercept. In P/V against P, the slope is 1/Vm. The intercept is 1/(KVm).
Using the Langmuir isotherm for multilayers. It assumes one layer. Physisorption near the boiling point of the gas forms many.
Writing θ=KP at all pressures. That is only the low pressure limit.
Remember these
θ=1+KPKP, and V=Vmθ.
VP=KVm1+VmP.
Half cover at P=1/K.
Dissociative: θ=1+KPKP.
Surface area: A=22400mL/molVmNAσ.
References
Atkins' Physical Chemistry, the chapter on processes at solid surfaces: the Langmuir and BET isotherms and the isosteric enthalpy.
I. Langmuir, Journal of the American Chemical Society, 1918, volume 40, page 1361.
Check yourself
Try each one on your own first. If you are stuck, open a hint. Then check with Show the answer.
A gas has K=0.25kPa−1 on a solid. At what pressure is the surface half covered?
Why does the Langmuir isotherm level off at high pressure while the Freundlich isotherm does not?
In a plot of P/V against P, the slope is 0.0125g/mL. What is the monolayer volume?
At low pressure, hydrogen on a metal is adsorbed in proportion to P1/2. What does that tell you about the hydrogen on the surface?
Enroll free in Adsorption: Physisorption, Chemisorption and Isotherms
Every lesson is open to read. Enrolling also lets you:
Mark lessons done and carry on where you stopped.
Take the tests of this lesson and its course.
Count the course towards the certificate for its chapter.