Adsorption at a surface: physisorption and chemisorption
A packet of silica gel keeps a camera bag dry, and a charcoal filter takes the smell out of air. Both hold molecules on a surface. This lesson explains why a surface attracts molecules, and how the weak hold of physisorption differs from the chemical bond of chemisorption.
about 25 min1 simulation1 practice question
Lesson 1 of 3Show all lessonsHide
Try the code and the simulations beside the lesson.
Molecules that stick to a surface
Think of a molecule deep inside a solid. Its neighbours pull it equally from every side. Now think of a molecule at the surface. It has neighbours only below it and beside it. The pull on it is unbalanced. So the surface can attract molecules of a gas or a solute and hold them there.
This piling up of molecules on a surface is called adsorption. The solid that holds the molecules is the adsorbent. The substance that is held is the adsorbate. The reverse process, when the molecules leave the surface, is desorption.
Adsorption is not absorption.
In adsorption the molecules stay on the surface. Their concentration at the surface is higher than in the bulk.
In absorption the molecules spread through the whole solid, as water spreads through a sponge.
When both happen together, as when a dye enters cotton fibres, we say sorption.
A chalk stick dipped in ink shows the difference. The colour stays on the outside (adsorption), but the water soaks in (absorption).
Why adsorption gives out heat
A gas molecule moves freely in three dimensions. Once it is held on a surface, it can move at most in two. So adsorption lowers the entropy: ΔS<0.
For a process that happens by itself, ΔG=ΔH−TΔS must be negative. With ΔS negative, −TΔS is positive. So ΔH must be negative, and large enough to win. Adsorption is therefore exothermic. The heat given out for each mole of adsorbate is the enthalpy of adsorption.
As adsorption goes on, the surface fills, ΔH becomes less negative, and at some point ΔG reaches zero. Then adsorption and desorption balance: this is adsorption equilibrium.
Physisorption and chemisorption
There are two kinds of adsorption, and they differ in the force that holds the molecule.
Physical adsorption (physisorption). The molecules are held by van der Waals forces, the same weak forces that hold a liquid together.
The enthalpy of adsorption is small, about −20 to −40kJ/mol.
It is not specific. Any gas is adsorbed on any solid to some extent.
It is reversible. Lower the pressure or warm the solid, and the gas comes off.
Several layers of molecules can form (multilayer).
It needs no activation energy and is fast.
It is greatest at low temperature and falls as the temperature rises.
Gases that are easily liquefied are adsorbed most. These gases have a high critical temperature and strong van der Waals forces. So SO2 and NH3 are taken up by charcoal far more than H2 or N2.
Chemical adsorption (chemisorption). The molecules form chemical bonds with the surface atoms.
The enthalpy of adsorption is large, about −80 to −240kJ/mol.
It is highly specific. Hydrogen is chemisorbed on nickel, but not on zinc.
It is often irreversible. A new surface compound may form, such as an oxide layer.
Only one layer forms (monolayer), because a bond needs a surface atom.
It often needs an activation energy, like any reaction.
It rises with temperature at first, then falls.
These enthalpy ranges are the ones the older NCERT book prints. Atkins' Physical Chemistry gives typical values of about −20kJ/mol for physisorption and about −200kJ/mol for chemisorption. The two sets agree on the idea: chemisorption is ten times stronger or more.
Often both happen with the same gas. Hydrogen on nickel is physisorbed at low temperature. At higher temperature it gains the activation energy and is chemisorbed, as hydrogen atoms.
How temperature, pressure and area change adsorption
A graph of the amount adsorbed against temperature, at a fixed pressure, is an adsorption isobar.
Two graphs side by side of the amount of gas adsorbed against the temperature at a fixed pressure. Left, physisorption: the amount is highest at the lowest temperature and falls smoothly as the temperature rises. Right, chemisorption: the amount is small at low temperature, rises to a maximum at a middle temperature, and then falls.
Temperature. Physisorption is exothermic. By Le Chatelier's principle, raising the temperature shifts the equilibrium back, so less is adsorbed. Chemisorption first rises, because more molecules have the activation energy. Then it falls, as for any exothermic equilibrium.
Pressure. More gas pressure pushes more molecules onto the surface, until the surface is full. The next two lessons follow this with an equation.
Surface area. The more surface for each gram, the more gas a gram can hold. Finely divided metals, porous charcoal and silica gel have huge areas. Activated charcoal is charcoal heated in steam to open its pores. One gram can have an area of about 1000m2.
How grinding opens up surface
A cube of edge d has six faces of area d2 and a volume d3. For a solid of density ρ, the area for each gram is
mA=ρd36d2=ρd6
The same ratio holds for a sphere of diameter d. Halve the grain size, and the area doubles.
Start at 1000 nm and move to 10 nm. The area grows a hundred times. A powder of grains 10 nm across has 300m2 in every gram.
Practise with new numbers
Try it in Python
The program works out the area of one gram of a solid for four grain sizes, and the nitrogen needed to cover it with one layer.
Common mistakes
Calling adsorption absorption. Adsorption is at the surface only.
Thinking adsorption can be endothermic. The entropy falls, so ΔH must be negative for the process to happen.
Saying chemisorption always falls with temperature. It first rises, because it needs activation energy.
Forgetting the nature of the gas. In physisorption, a gas with a higher critical temperature is adsorbed more.
Remember these
Adsorption: ΔS<0, so ΔH<0.
Physisorption: van der Waals forces, about −20 to −40kJ/mol, multilayer, reversible, falls with temperature.
Chemisorption: chemical bonds, about −80 to −240kJ/mol, monolayer, specific, needs activation energy.
Area for each gram: mA=ρd6.
References
NCERT Chemistry Part I for Class 12 (edition before 2023), Unit 5, Surface Chemistry, section 5.1.
Atkins' Physical Chemistry, the chapter on processes at solid surfaces.
Check yourself
Try each one on your own first. If you are stuck, open a hint. Then check with Show the answer.
Why must a gas be adsorbed with a release of heat?
Charcoal at the same temperature and pressure is offered methane and sulphur dioxide. Which is adsorbed more, and why?
Hydrogen on nickel is adsorbed more at 300 K than at 100 K, at the same pressure. Is that physisorption?
A grain of a solid is ground into pieces one hundredth of its size. By what factor does the area of each gram change?
Enroll free in Adsorption: Physisorption, Chemisorption and Isotherms
Every lesson is open to read. Enrolling also lets you:
Mark lessons done and carry on where you stopped.
Take the tests of this lesson and its course.
Count the course towards the certificate for its chapter.