The Freundlich isotherm and adsorption from solution
How much gas does a gram of charcoal hold at a given pressure? In 1909 Herbert Freundlich wrote a simple rule that fits many such readings. This lesson shows the rule, how to find its two constants from a straight line, and how the same rule works for a solute held from a solution.
about 25 min1 simulation1 practice question
Lesson 2 of 3Show all lessonsHide
Try the code and the simulations beside the lesson.
The amount adsorbed and the pressure
We measure adsorption as x/m: the mass (or the amount in moles) of gas x held by a mass m of adsorbent. A graph of x/m against the pressure P, at a fixed temperature, is an adsorption isotherm.
Readings for many gases on charcoal show the same shape. At low pressure, x/m rises almost in proportion to P. At higher pressure, the rise slows. At very high pressure, x/m stops growing, because the surface is full.
The Freundlich isotherm
Freundlich fitted the middle range with a power of the pressure:
mx=kP1/n
Here k and n are constants for a given gas, adsorbent and temperature, and n>1. So the exponent 1/n lies between 0 and 1.
If 1/n=1, then x/m=kP: the amount is proportional to the pressure. This is the low pressure end.
If 1/n=0, then x/m=k: the amount does not depend on the pressure. This is the high pressure end, a full surface.
In between, the curve bends over. The smaller 1/n, the sooner it flattens.
The Freundlich isotherm is an empirical rule: it describes readings but has no model behind it. It fails at high pressure, because kP1/n keeps growing while a real surface fills up.
A straight line from the readings
Take logarithms of both sides:
logmx=logk+n1logP
This is the equation of a straight line. Plot log(x/m) on the vertical axis against logP on the horizontal axis.
The slope is 1/n.
The intercept on the vertical axis (where logP=0, so P=1 in the units used) is logk.
Two graphs of the Freundlich isotherm. Left: x over m against the pressure for three values of 1 over n. With 1 over n equal to 1 the line is straight; with 0.5 and 0.2 the curves bend over more and more. Right: the logarithm of x over m against the logarithm of the pressure. All three are straight lines that meet the vertical axis at log k, with slopes 1, 0.5 and 0.2.
The value of k depends on the unit of pressure. Always state it with its unit, such as mmol/g at 1kPa.
Set 1/n=1 and double the pressure: the amount doubles. Set 1/n=0.25 and double it again. The amount rises by only 20.25=1.19 times.
Practise with new numbers
Adsorption from a solution
A solid also takes solutes out of a solution. Shake charcoal with a dilute solution of acetic acid, and the concentration of the acid falls. Charcoal also removes the colour from raw sugar solution, and alumina takes up dyes.
The same rule fits, with the concentration C at equilibrium in place of the pressure:
mx=kC1/n
The experiment. Put the same mass of activated charcoal into several flasks. Add a known volume of acetic acid of a different concentration to each. Shake them for an hour at a fixed temperature, then filter. Titrate a portion of each filtrate with standard sodium hydroxide. The fall in concentration gives the acid taken up.
Amount adsorbed =(C0−C)×V, where C0 is the starting concentration and V the volume.
Divide by the mass of charcoal to get x/m.
Plot log(x/m) against logC, and read 1/n and k from the line.
Precautions. Use the same temperature in every flask, because adsorption falls as the temperature rises. Throw away the first few millilitres of each filtrate, because the filter paper also takes up a little acid.
Where adsorption is used
Gas masks hold activated charcoal, which takes up poisonous gases and lets air through.
Silica gel and alumina take moisture out of air and keep it dry.
Decolourising: charcoal removes coloured impurities from sugar solutions.
Chromatography: substances in a mixture are held on a column of alumina or silica to different extents, so they separate.
Froth flotation: pine oil and a frothing agent are adsorbed on the grains of a sulphide ore, which rise with the froth and leave the rock behind.
Adsorption indicators: in a precipitation titration, a dye such as fluorescein is adsorbed on the precipitate at the end point and changes its colour.
Heterogeneous catalysis: reactants are adsorbed on a metal surface and react there. This is the subject of the next course.
Try it in Python
The program fits a straight line to log(x/m) against logP, reads 1/n and k, and predicts x/m at a new pressure.
Common mistakes
Reading n from the slope. The slope is 1/n, not n.
Reading k from the intercept directly. The intercept is logk, so k=10intercept.
Using the starting concentration in the isotherm. The isotherm uses the concentration left at equilibrium.
Trusting the Freundlich rule at very high pressure. It does not show the surface filling up.
Remember these
mx=kP1/n, with 0<1/n<1.
logmx=logk+n1logP: slope 1/n, intercept logk.
From solution: mx=kC1/n, with the concentration at equilibrium.
References
NCERT Chemistry Part I for Class 12 (edition before 2023), Unit 5, Surface Chemistry, sections 5.1.4 and 5.1.5.
Atkins' Physical Chemistry, the chapter on processes at solid surfaces.
Check yourself
Try each one on your own first. If you are stuck, open a hint. Then check with Show the answer.
A plot of log(x/m) against logP has a slope of 0.25. What happens to x/m when P is multiplied by 16?
Why can the exponent 1/n not be larger than 1 for adsorption on a solid?
In the acetic acid experiment, why must every flask be at the same temperature?
What does an intercept of 0 on the log(x/m) axis tell you?
Enroll free in Adsorption: Physisorption, Chemisorption and Isotherms
Every lesson is open to read. Enrolling also lets you:
Mark lessons done and carry on where you stopped.
Take the tests of this lesson and its course.
Count the course towards the certificate for its chapter.