Centre of gravity and stability · Physics Class 9–10 | StemPy Lab
Course 13.2·Lesson 3 of 3
Centre of gravity and stability
Hold a ruler flat on one finger and it balances at one point. That point is the centre of gravity. This lesson defines it, finds it for a flat card of any shape, and uses it to explain why some objects tip over more easily than others.
about 35 min1 simulation2 practice questions1 Python program5 questions to check yourself
This lesson is free to read. Enroll free to keep your place in the course.
Lesson 3 of 3Show all lessonsHide
Try the code and the simulations beside the lesson.
The weight of an object acts at a point
Every particle of an object has weight. All these small weights add up to the weight of the whole object. For many questions we can replace them by one single force, acting at one single point.
The centre of gravity of an object is the point through which the whole weight of the object can be considered to act.
For a regular object of the same material all through, the centre of gravity is at its middle: the middle of a metre rule, the centre of a ball, the point where the diagonals of a rectangle cross. It can be outside the object. The centre of gravity of a ring is in the empty hole.
An experiment: the centre of gravity of an irregular lamina
A lamina is a thin flat sheet, such as a piece of card. Cut an irregular shape, and make three small holes near its edge, A, B and C.
Two pictures of an irregular five-sided lamina of card. On the left it hangs from a pin at hole A. A blue plumb line hangs straight down from the pin, passing through a red cross that marks the centre of gravity. On the right the lamina lies flat with three small holes A, B and C near its edge. Three lines drawn from the holes, one blue, one green and one purple, cross at the same point, which is marked as the centre of gravity.
Hang the lamina from a pin through hole A. It can swing freely. It stops when its centre of gravity is directly below the pin. If it were not, the weight would have a moment about the pin and the lamina would keep turning.
Hang a plumb line (a thread with a small weight) from the same pin. It hangs straight down.
Mark the line on the lamina with a pencil. The centre of gravity is somewhere on this line.
Repeat from hole B and from hole C.
The lines cross at one point. That point is the centre of gravity. As a check, balance the lamina on the point of a pencil.
Use at least two holes. A third line is a check on the accuracy.
Stability
An object is stable if it returns to its position after a small tilt. Look at the three blocks in the picture. When a block is tipped about its bottom corner, its weight acts at the centre of gravity. As long as the vertical line through the centre of gravity falls inside the base, the weight turns the block back. When the line falls outside the base, the weight turns the block over.
Three pictures of a tall rectangular block tipped about its bottom right corner, each with a red dot at its centre of gravity and a red dashed vertical line down from the dot to the ground. In the first the block is tilted a little, and the dashed line lands inside the base, to the left of the corner, so the block falls back. In the second the tilt is at the critical angle of about 22 degrees and the dashed line lands exactly on the corner. In the third the tilt is 32 degrees, the line lands outside the base to the right of the corner, and the block topples.
So the stability of an object depends on two things:
The height of the centre of gravity. The lower it is, the more stable the object.
The width of the base. The wider it is, the more stable the object.
Racing cars are low and wide. A double-decker bus is tested at a tilt with a full load upstairs. A table lamp has a wide heavy base. A tall, narrow object with a high centre of gravity topples easily.
Try a block that is 1.0 m wide and 4.0 m high, and one that is 3.0 m wide and 1.0 m high. Which has the bigger critical angle? Which is more stable?
A little further (a calculation that the exam does not ask for). A rectangular block topples when its centre of gravity is directly above the bottom corner that it is tipped about. The centre of gravity is half the width across and half the height up. So tanθc=hw.
For a box 0.50 m wide and 1.20 m high, θc=22.6∘. Laid on its side, the same box has a width of 1.20 m and a height of 0.50 m, so θc=67.4∘. It is much harder to topple.
Extended: the weight of a beam in moments
A uniform beam has its weight at its middle. Use that in the principle of moments.
A worked example. A uniform plank of weight 80 N and length 2.0 m is balanced on a pivot 0.4 m from one end. A load W hangs from that end.
The distances. The middle of the plank is 1.0 m from the end, so it is 0.6 m from the pivot.
Equal moments.W×0.4=80×0.6.
The load.W=0.480×0.6=120N.
The pivot. The upward force is 80+120=200N.
Practise with new numbers
Try it in Python
The program finds the centre of gravity of an L-shaped lamina by treating each rectangle as a weight at its middle. This is a step beyond the exam, and it uses the principle of moments.
Common mistakes
Saying the centre of gravity is always in the object. It can be outside, as in a ring.
Marking only one line on the lamina. One line is not enough. The centre of gravity is where the lines cross.
Saying that a heavy object is always stable. Stability depends on the position of the centre of gravity and the width of the base.
Forgetting the weight of a beam in a moment calculation. It acts at the middle of a uniform beam.
Looking at the corner instead of the vertical line. The test is whether the line down from the centre of gravity falls inside the base.
Remember these
Centre of gravity: the point through which the whole weight can be considered to act.
To find it for a lamina: hang it from a pin at several holes, mark the plumb line each time, and find where the lines cross.
A lower centre of gravity and a wider base make an object more stable.
An object topples when the vertical line from its centre of gravity falls outside its base.
Check yourself
Try each one on your own first. If you are stuck, open a hint. Then check with Show the answer.
In your own words, what is the centre of gravity of an object?
Why must you hang the lamina from at least two holes?
Why is a cone standing on its flat base more stable than the same cone balanced on its point?
A box is 0.30 m wide and 0.90 m high. At what angle does it topple? Extended. Also: a uniform plank of weight 60 N and length 3.0 m balances on a pivot 0.60 m from one end. What load hangs from that end?
References
Cambridge IGCSE Physics 0625 syllabus, section 1.5.3: the centre of gravity, the lamina experiment and stability.
OpenStax, College Physics 2e, Chapter 9 (Statics and Torque): centre of gravity and stability.
Enroll free in Moments and Centre of Gravity
Every lesson is open to read. Enrolling also lets you:
Mark lessons done and carry on where you stopped.
Count the course towards the certificate for its chapter.