Length and volume with rulers and cylinders · Physics… | StemPy Lab
Course 13.1·Lesson 1 of 3
Length and volume with rulers and cylinders
A measurement is a number with a unit, and its quality depends on how you read the instrument. This lesson shows how to read a ruler and a measuring cylinder, how to find the volume of a block and of a stone, and how to write the reading down.
about 30 min1 simulation2 practice questions
Lesson 1 of 3Show all lessonsHide
Try the code and the simulations beside the lesson.
Why a careful reading matters
A tailor measures a sleeve. A cook measures milk. Both read a scale. A small habit, such as where the eye is, can change the reading. In science we measure length, volume, time and many other quantities. This lesson is about length and volume. The next lesson is about time.
Every measurement has two parts: a number and a unit. "7.4" means nothing. "7.4 cm" is a length.
You may meet vernier callipers and the screw gauge in the Class 11-12 chapters on Units and Measurement and on Experimental Skills. Here we use the simple tools that every laboratory has: the ruler and the measuring cylinder.
Measuring length with a ruler
A school ruler is 30 cm long. It has a mark at every millimetre (mm). The smallest division is 1 mm, which is 0.1 cm.
A ruler graduated in millimetres with numbers from 0 to 12 centimetres. A block lies along it with its left end at the 1.0 centimetre mark and its right end at the 8.4 centimetre mark. The label says that the length is 8.4 minus 1.0, which is 7.4 cm.
To measure a length:
Put the zero mark of the ruler against one end of the object. If the end of the ruler is worn, start from a clear mark such as 1.0 cm and subtract it at the end.
Keep your eye straight above the mark that you read. A reading taken from the side is wrong, because the scale seems to shift against the object. This error is called parallax.
Read the mark at the other end. If the end falls between two marks, estimate the reading to half a division, which is 0.5 mm.
Write the number and the unit.
In the picture, the block starts at 1.0 cm and ends at 8.4 cm. The length is 8.4−1.0=7.4cm.
Writing the reading down
Write a reading to the precision of the instrument. This means that the number of decimal places shows the smallest step that the instrument can show. A ruler with millimetre marks gives a length in centimetres to one decimal place, such as 7.4 cm. Do not write 7.4000 cm, because the ruler cannot show that. In a table, put the name and the unit in the heading, written as length / cm, and write only numbers under it.
Measuring volume with a measuring cylinder
A measuring cylinder is a tall glass or plastic tube with a scale of volume. The scale is in cubic centimetres (cm³). One cubic centimetre is the same as one millilitre (mL).
Two measuring cylinders side by side, graduated from 0 to 50 cm cubed. The left one holds water only, and the bottom of its curved water surface is at the 30 mark; a red arrow at eye level points to it. The right one holds water and a stone at the bottom, and the water level has risen to 42. A note says the stone volume is 42 minus 30, which is 12 cm cubed.
Stand the cylinder on a flat table.
The surface of water is curved, and the curve is called the meniscus. Read the scale at the bottom of the curve.
Put your eye level with the surface, as the red arrow shows. The scale is on the front of the cylinder, and the liquid is behind it. An eye above the surface reads too high, and an eye below it reads too low.
Choose the smallest cylinder that can hold the liquid. Its marks are closer together, so the reading is more precise.
The volume of a solid
A rectangular block.V=l×w×h. A block 4.0 cm by 3.0 cm by 2.5 cm has V=4.0×3.0×2.5=30.0cm3.
A cylinder.V=πr2h, where r is the radius of the circular end and h is the height.
An irregular solid. Pour water into a measuring cylinder and read the level, V1. Lower the solid into the water with a thread. Read the new level, V2. The solid pushes the water up by its own volume, so V=V2−V1.
The stone in the picture raises the water from 30 cm³ to 42 cm³. Its volume is 42 − 30 = 12 cm³.
Move the sliders. The red line is always above the blue one by the volume of the stone.
Changing units of volume
1cm3=1mL and 1000cm3=1litre.
1m3=1000000cm3, so 1cm3=10−6m3.
The block above has V=30.0cm3=3.0×10−5m3.
Practise with new numbers
Try it in Python
The program finds the volume of a stone from three trials, and then the volume of a block in cm³ and m³.
Common mistakes
Reading the top of the meniscus. Read the bottom of the curve.
Looking at the scale from above or below. Put your eye level with the mark.
Starting from a worn end. Use a clear mark and subtract it.
Writing a number without a unit. "7.4" is not a length. Write "7.4 cm".
Adding the two readings of a displacement. The volume of the solid is the rise of the level: V2−V1.
Mixing cm³ and m³.1m3 is a million cm³, not a thousand.
Remember these
A ruler with millimetre marks: read to half a millimetre, with the eye straight above the mark.
A measuring cylinder: eye level with the bottom of the meniscus. Volume in cm³.