A white powder turns blue in a drop of water, and a blue paper turns pink. Neither test tells you that the water is clean. You learn the two chemical tests for water and how melting points and boiling points show purity.
about 30 min1 simulation2 practice questions
Lesson 1 of 3Show all lessonsHide
Try the code and the simulations beside the lesson.
How do you show that a liquid is water?
You cannot tell by looking. Many clear liquids look like water. Chemists use a chemical test, which is a reaction with a clear colour change. There are two for water.
Anhydrous copper(II) sulfate is a white powder. Anhydrous means "without water". If water is added, it turns blue.
Anhydrous cobalt(II) chloride is a blue solid, often made as a blue paper. If water is added, it turns pink.
CuSO4+5H2O→CuSO4⋅5H2O
The blue solid is hydrated copper(II) sulfate. It holds five molecules of water in its crystals. You met water of crystallisation in the chapter on acids, bases and salts.
Two tests for water side by side. On the left, a watch glass of white anhydrous copper(II) sulfate powder and an arrow labelled add water to a watch glass of blue powder. On the right, a strip of blue cobalt(II) chloride paper and an arrow labelled add water to a pink strip. A line under both says: these tests show that water is present, not that it is pure.
Both tests show that water is present. They do not show that the water is pure. Salt solution and orange juice also turn the white powder blue, because both contain water.
How do you show that water is pure?
A pure substance has a fixed melting point and a fixed boiling point. For pure water, at normal atmospheric pressure (101.3kPa):
it melts at 0∘C,
it boils at 100∘C.
Impurities change both. A dissolved impurity lowers the melting point and raises the boiling point. The change also spreads over a range of temperatures. Salt water, for example, freezes below 0∘C and boils a little above 100∘C.
So the test is simple. Heat the sample with a thermometer in it. If it boils at exactly 100∘C and stays there, it is pure water. If it boils at another temperature, or the temperature keeps creeping up, it is not pure. You get the same result by cooling it until it freezes.
A graph of temperature in degrees Celsius against time while water is heated. The line for pure water rises and then stays level at 100 degrees Celsius while it boils. A second line for a salt solution rises above 100 degrees Celsius and keeps climbing slowly while it boils. A label says that an impure sample boils over a range of temperatures, higher than 100 degrees Celsius.
Why do we use distilled water in the laboratory?
Tap water has a clean look and a pleasant taste, but it is not pure. It holds dissolved salts, such as calcium and magnesium compounds, and chloride ions from the chlorine used to treat it. These chemical impurities can spoil an experiment.
Suppose you test a solution for chloride ions with silver nitrate. Tap water would give a white precipitate by itself. Distilled water is made by distillation. The water boils and is condensed again, and the dissolved solids stay behind. It has far fewer chemical impurities, so the result of the experiment is the result of your sample and nothing else.
You should find that the water needed is a little over half of the mass of the white powder. The solid gains mass until it is all blue. After that, extra water stays as water.
Practise with new numbers
Try it in Python
This program works out how much water a sample of white copper(II) sulfate takes in, and how much blue solid it makes.
Common mistakes
Saying that a blue colour with copper(II) sulfate proves the water is pure. It proves only that water is present.
Turning the colours the wrong way round. White goes to blue with copper(II) sulfate. Blue goes to pink with cobalt(II) chloride.
Saying that impurities raise the melting point. They lower it. They raise the boiling point.
Using tap water for a test for ions. Dissolved salts in it can give a false result.
Remember these
Water turns white anhydrous copper(II) sulfate blue and blue anhydrous cobalt(II) chloride pink.
Pure water melts at 0∘C and boils at 100∘C. Impurities lower the melting point, raise the boiling point and make a range.
Distilled water is used in practical work because it has fewer chemical impurities than tap water.
Check yourself
Try each one on your own first. If you are stuck, open a hint. Then check with Show the answer.
Describe the colour change when water is added to anhydrous copper(II) sulfate.
Describe the colour change when water is added to anhydrous cobalt(II) chloride.
A colourless liquid boils at 104∘C. Is it pure water? Give a reason.
Why is distilled water used in a school laboratory instead of tap water?
A student says that a liquid is pure water because it turns copper(II) sulfate blue. Explain the mistake.