A firework is over in a flash, and an iron nail takes months to rust. Chemists give each reaction a rate. This lesson explains what the rate means and shows two ways to measure it.
about 30 min1 simulation2 practice questions
Lesson 1 of 3Show all lessonsHide
Try the code and the simulations beside the lesson.
Fast and slow reactions
Some reactions are very fast. The burning of gunpowder in a firework and the forming of a white solid when two clear solutions are mixed take about a second. Other reactions are slow. An iron nail takes months to rust, and a limestone statue takes centuries to weather.
The rate of a reaction tells you how fast it goes. A fast reaction has a high rate and a slow reaction has a low rate.
What is the rate?
A reaction makes products and uses up reactants. We can measure how much of a product forms in each second, or how much of a reactant is used up in each second. So:
rate=time takenamount made
Here "amount made" means the amount of product formed, or the amount of reactant used up.
The unit depends on what you measure.
A gas: cm³/s (cubic centimetres of gas in each second).
A mass: g/s or g/min (grams in each second or each minute).
An amount of substance: mol/s.
A rate worked out over a stretch of time is a mean rate. It is the average speed of the reaction over that time, like the average speed of a car on a journey.
Two ways to measure the rate
Take the reaction of marble chips (calcium carbonate) with dilute hydrochloric acid. It makes a gas.
CaCO3+2HCl→CaCl2+H2O+CO2
You can follow it in two ways. Both measure how much carbon dioxide has been made, at the start and then at fixed times.
A drawing of two ways to follow a reaction between marble chips and acid. On the left, a conical flask is closed with a bung. A delivery tube leads from the bung to a gas syringe, and the gas pushes the plunger out, so the volume of gas can be read. On the right, a conical flask with a plug of cotton wool in its neck stands on a balance that reads 62.40 g. Carbon dioxide escapes through the cotton wool, so the reading falls.
Volume of gas. The carbon dioxide goes along a tube into a gas syringe. You read the volume every 20 seconds.
Loss of mass. The flask stands on a balance. The carbon dioxide escapes, so the mass of the flask and its contents falls. You read the balance every 20 seconds. A plug of cotton wool in the neck lets the gas out but stops drops of acid from spraying out.
The mass method works well when the gas is heavy, such as carbon dioxide. It works badly for hydrogen, because hydrogen is so light that the mass change is tiny.
A table of readings
A student collects carbon dioxide in a gas syringe and records the volume every 20 s.
At 0 s: 0 cm³. At 20 s: 18 cm³. At 40 s: 32 cm³.
At 60 s: 42 cm³. At 80 s: 48 cm³. At 100 s: 50 cm³.
The mean rate in each interval is the volume made in that interval divided by its time. From 0 to 20 s the syringe gains 18 cm³, so the mean rate is 2018=0.9cm3/s. From 20 to 40 s it gains 14 cm³, so the rate is 0.7cm3/s. The next intervals give 0.5, 0.3 and 0.1cm3/s.
The rate gets smaller all the time. The reason is that the reactants are used up. There are fewer acid particles and less marble surface left, so the reaction slows down. After 100 s there is almost no change.
The first part of the curve is steep, and the end is flat. The mean rate from the start is largest at the early times.
Practise with new numbers
Try it in Python
The program works out the rate in each interval and the mean rate for the whole run.
Common mistakes
Dividing the time by the volume. The rate is how much is made in each second, so the volume goes on top.
Leaving out the unit. A rate always has a unit with a time in it, such as cm³/s.
Thinking the rate stays the same. Most reactions start fast and slow down, so a mean rate is only an average.
Using a balance for a very light gas. Hydrogen escapes with almost no change in mass.
Forgetting the cotton wool. Without it, drops of acid leave the flask and the mass falls too much.
Remember these
Rate = amount of product formed (or reactant used) divided by the time taken.
Units: cm³/s for a gas, g/s or g/min for a mass, mol/s for an amount.
Two methods for a gas: collect the volume in a gas syringe, or measure the loss of mass on a balance.
A reaction slows down as the reactants are used up.
Check yourself
Try each one on your own first. If you are stuck, open a hint. Then check with Show the answer.
A reaction makes 36cm3 of gas in 12 s. What is the mean rate?
Why does the mass of the flask fall when marble chips react with acid on a balance?
Why is a gas syringe better than a balance for following magnesium with acid?
Why does the rate of a reaction usually fall during the experiment?
A flask loses 0.45 g in 90 s. What is the mean rate in g/min?
References
Cambridge IGCSE Chemistry 0620 syllabus for 2026 to 2028, section 6.2 (Rate of reaction), Core 3 and Supplement 8.