Most polythene, PVC and polystyrene are made by a free-radical chain. This lesson follows the chain through initiation, propagation and termination, shows how the amount of initiator sets the chain length, and compares the routes to low and high density polythene.
about 25 min1 simulation1 practice question
Lesson 2 of 3Show all lessonsHide
Try the code and the simulations beside the lesson.
One radical, a thousand monomers
Imagine a line of people holding hands. One person reaches out and takes the hand of the next, who reaches for the next, and so on. A free-radical chain works in the same way. A single reactive species starts it, and it adds monomer after monomer until it meets another radical.
A free radical is an atom or group with an unpaired electron. It is very reactive. It attacks the electron pair of a carbon to carbon double bond.
The three stages
The free-radical chain mechanism in three stages, one under the other. Initiation: benzoyl peroxide splits into two benzoyloxy radicals, each loses carbon dioxide and gives a phenyl radical, and the phenyl radical adds to ethene to give a new carbon radical. Propagation: the carbon radical adds to another ethene molecule again and again, so the chain grows by two carbon atoms each time. Termination: two chain radicals meet. In combination they join into one long chain. In disproportionation one radical takes a hydrogen atom from the other, giving one chain with a saturated end and one chain with a double bond at its end.
1. Initiation. An initiator such as benzoyl peroxide is heated. Its weak O-O bond breaks evenly, and each half takes one electron.
C6H5CO-O-O-COC6H5→2C6H5COO∙
C6H5COO∙→C6H5∙+CO2
The phenyl radical adds to a monomer. A new carbon radical forms at the far end:
C6H5∙+CH2=CH2→C6H5-CH2-CH2∙
2. Propagation. The new radical adds to another monomer, and again, and again:
Each step makes a new radical at the end, so the chain keeps growing. With a substituted monomer such as styrene, CH2=CH-C6H5, the radical adds to the CH2 end. The new radical then sits on the carbon that carries the ring, where it is stabilised. So the units join head to tail.
3. Termination. Two growing radicals meet.
In combination, they join into one chain. Two radicals give one dead chain.
In disproportionation, one radical takes a hydrogen atom from its neighbour. Two radicals give two dead chains, one with a saturated end and one with a C=C at its end.
Polystyrene chains end mainly by combination. Chains of poly(methyl methacrylate) end mainly by disproportionation.
How the initiator sets the chain length
Each initiator molecule gives two radicals. Only a fraction f of them start chains; the rest are lost in side reactions. Suppose a mass m of polymer forms.
With combination, the number of chains is half the number of radicals that grew.
With disproportionation, it equals the number of radicals that grew.
Mn=nchainsm
More initiator gives more chains, so each chain is shorter. A factory that wants long chains uses very little initiator.
Double the initiator from 1 mmol to 2 mmol. The molar mass halves. Now switch to disproportionation. The chains are again half as long, because each radical ends as its own chain.
Low and high density polythene
Product
Conditions
Chains
Low density
1000 to 2000 atm, 350 to 570 K, peroxide
branched
High density
Ziegler-Natta, 6 to 7 atm, 333 to 343 K
linear
Low density polythene forms by the free-radical chain at high pressure. A growing radical often takes a hydrogen atom from its own chain a few carbons back, so the chain branches. Its density is about 0.92g/cm3. It is tough and flexible: squeeze bottles, toys, flexible pipes and the insulation of electric wires.
High density polythene forms on a Ziegler-Natta catalyst, triethylaluminium with titanium(IV) chloride, in a hydrocarbon solvent. The monomer adds at a titanium centre, not by a free radical, so there is almost no branching. The linear chains pack well. Its density is about 0.97g/cm3. It is stiffer and stronger: buckets, dustbins, bottles and pipes.
Other ways to start a chain (olympiad depth)
Cationic chains start with an acid, such as boron trifluoride with a trace of water. They suit monomers that give a stable carbocation, such as 2-methylpropene.
Anionic chains start with a strong base, such as butyllithium. They suit monomers with an electron-withdrawing group, such as acrylonitrile. With no impurities they do not stop, so they are called living chains.
Coordination on a Ziegler-Natta catalyst also controls how the side groups point. In isotactic polypropene all methyl groups lie on one side of the chain; in syndiotactic they alternate; in atactic they are random. Isotactic chains pack into crystals and give a hard plastic.
Practise with new numbers
Try it in Python
The program counts the radicals and the chains for both kinds of termination, and prints the molar mass in each case.
Common mistakes
Forgetting that each peroxide gives two radicals. One O-O bond breaks into two halves.
Taking one chain per radical for combination. Two radicals become one chain.
Thinking more initiator gives longer chains. It gives more chains, each shorter.
Saying high density polythene is made by free radicals. It is made on a Ziegler-Natta catalyst.
Writing styrene units head to head. The radical sits on the carbon with the ring, so units join head to tail.