Copper wire carries a current, glass does not, and silicon sits in between. A magnet picks up an iron nail but not a copper coin. Both facts come from the electrons of the solid. We use a simple picture of energy bands for conduction, see how a trace of an impurity changes a semiconductor, and sort solids by the way they respond to a magnet.
about 35 min1 simulation2 practice questions
Lesson 3 of 3Show all lessonsHide
Try the code and the simulations beside the lesson.
Three classes by conductivity
Solids span a huge range of electrical conductivity, σ, measured in Ω−1m−1 (siemens per metre):
Conductors: 104 to 107Ω−1m−1. Metals.
Semiconductors: 10−6 to 104Ω−1m−1. Silicon, germanium, gallium arsenide.
Insulators: 10−20 to 10−10Ω−1m−1. Glass, diamond, most salts and plastics.
These ranges are the ones in NCERT. Other books draw the lines a little differently. That is a whole factor of 1027 from the best insulator to the best metal.
Energy bands
In one atom, an electron has sharp energy levels. Bring N atoms together and each level splits into N levels so close together that they form a band. A crystal has 1022 or more atoms, so the band is practically a smooth range of energies.
The highest band that holds electrons is the valence band.
The next band above it is the conduction band.
The range between them, with no allowed levels, is the band gap, Eg, measured in electronvolts (1eV=1.602×10−19J).
An electron can carry a current only if it can move into a slightly higher empty level. A completely full band carries no current.
Three energy band diagrams side by side. Metal: the lower band is partly filled (shaded part) and touches the empty band, so there is no gap. Semiconductor: a filled valence band and an empty conduction band with a small gap between them, labelled about 1 eV. Insulator: a filled valence band and an empty conduction band with a large gap, labelled more than 3 eV.
Metals. The valence band is partly filled, or it overlaps the conduction band. Electrons move at once.
Semiconductors. The gap is small, about 1eV: 1.12eV for silicon and 0.67eV for germanium. Some electrons jump the gap by thermal energy, and more as the temperature rises.
Insulators. The gap is large, more than about 3eV: about 5.5eV for diamond. Almost no electron can jump it.
So heating has opposite effects. In a metal, heating makes the ions vibrate more and scatter the electrons, and the conductivity falls. In a semiconductor, heating lifts more electrons across the gap, and the conductivity rises.
A pure semiconductor and its holes
In pure silicon each atom forms four bonds. When an electron jumps to the conduction band, it leaves an empty place in a bond, a hole. A neighbouring electron can fill the hole, which moves the hole. A hole behaves like a positive charge. Pure silicon has equal numbers of electrons and holes. It is an intrinsic semiconductor, and its conductivity is low.
Doping: n type and p type
Adding a tiny, controlled amount of an impurity is called doping. It makes an extrinsic semiconductor.
n type. Add a group 15 element, such as phosphorus or arsenic, to silicon (group 14). Four of its five valence electrons form bonds, and the fifth is free. The extra negative carriers give the name n type.
p type. Add a group 13 element, such as boron, aluminium or gallium. It has only three valence electrons, so one bond lacks an electron. That hole is a positive carrier, so the material is p type.
Even one dopant atom in a million silicon atoms raises the carrier density far above that of pure silicon. A junction of n and p type material is the diode, the basis of every chip and solar cell.
Compounds can act as semiconductors too. Pairs of groups 13 and 15 (13-15 compounds) such as GaAs, InSb and AlP have four valence electrons on average, as silicon does. Pairs of groups 12 and 16 (12-16 compounds) such as ZnS, CdS, CdSe and HgTe do the same. Many are used in light-emitting diodes and solar cells.
The gap and the colour
A photon is absorbed only if its energy hν is at least Eg. With hc=1240eV nm, the longest wavelength absorbed is
λmax=Eg1240eV nm
For silicon, 1.121240=1107nm, in the infrared. Silicon absorbs all visible light and looks dark grey. Diamond, at 5.5eV, absorbs only below 225nm, so all visible light passes and it is clear.
Try silicon at 1.12eV and diamond at 5.5eV. Then find the gap that gives an edge at 500nm.
Magnetic properties
Each electron acts as a tiny magnet. It has a moment from its spin and one from its motion around the nucleus. Two paired electrons cancel. The moment is measured in Bohr magnetons: 1BM=9.274×10−24J/T. For n unpaired electrons the spin-only moment is
μ=n(n+2)BM
Solids fall into five classes:
Diamagnetic. All electrons paired. Weakly pushed out of a magnetic field. Examples: NaCl, water, benzene, TiO2, V2O5.
Paramagnetic. Unpaired electrons whose moments point at random. Weakly pulled into a field, and the effect vanishes when the field is removed. Examples: O2, Cu2+, Fe3+ and Cr3+ salts.
Ferromagnetic. Moments line up in the same direction inside regions called domains. A field lines up the domains, and the solid stays a magnet afterwards. Strongly attracted. Examples: iron, cobalt, nickel, gadolinium, CrO2.
Antiferromagnetic. Moments line up in equal numbers in opposite directions and cancel. No net moment. Example: MnO.
Ferrimagnetic. Moments line up in opposite directions but in unequal amounts, so a net moment remains. Examples: magnetite Fe3O4, and ferrites such as MgFe2O4 and ZnFe2O4.
Heat destroys the order. Above a temperature called the Curie temperature, a ferromagnet becomes paramagnetic. Iron loses its magnetism at 770∘C. Ferrimagnets also turn paramagnetic on heating.
Practise with new numbers
Try it in Python
The program finds the absorption edge of several solids from their band gaps, says whether each looks clear, coloured or dark, and finds spin-only moments.
Common mistakes
Saying heating raises the conductivity of a metal. It lowers it. Heating raises the conductivity of a semiconductor.
Saying p type silicon has a positive charge. The crystal is neutral. Only its moving carriers are mostly holes.
Doping silicon with a group 16 element to make p type. p type needs a group 13 element, with one electron fewer than silicon.
Mixing up antiferromagnetic and ferrimagnetic. Both have opposite moments. Ferrimagnetic ones do not cancel.
Thinking a band gap is in joules per mole. It is usually given in electronvolts per electron.
Remember these
Metals: no gap. Semiconductors: gap near 1eV. Insulators: gap above about 3eV.
Heating lowers the conductivity of a metal and raises that of a semiconductor.
Group 15 in silicon gives n type, group 13 gives p type. 13-15 and 12-16 compounds are semiconductors.
λmax=1240eV nm/Eg.
Dia, para, ferro, antiferro and ferrimagnetic. μ=n(n+2) BM.
Check yourself
Try each one on your own first. If you are stuck, open a hint. Then check with Show the answer.
Germanium is doped with gallium. Which type of semiconductor results, and what are the main carriers?
Why does the conductivity of a semiconductor rise when it is heated?
What is the spin-only moment of Fe3+, which has 5 unpaired electrons?
Fe3O4 has unpaired electrons whose moments point in opposite directions, yet it is attracted strongly by a magnet. Which class is it?
Zinc sulphide has a band gap of about 3.6eV. Is it clear or coloured, when pure?
References
OpenStax, Chemistry 2e, Chapter 8 and Chapter 10, on band theory in brief. OpenStax, University Physics Volume 3, Chapter 9 (Condensed Matter Physics), on semiconductors and doping.
The band gaps of silicon and germanium are the standard values at room temperature. NCERT, Chemistry Part I for Class XII, Unit 1, editions before 2023, gives the conductivity ranges.
Enroll free in Ionic Structures, Defects and Properties of Solids
Every lesson is open to read. Enrolling also lets you:
Mark lessons done and carry on where you stopped.
Take the tests of this lesson and its course.
Count the course towards the certificate for its chapter.