Course 34.3Lesson 2 of 3
A builder mixes lime, sand and water, and a few days later the wall is hard. A doctor sets a broken arm in plaster, and in minutes the cast is firm. This lesson follows calcium compounds from limestone to quicklime, slaked lime, plaster of Paris and cement.
Try the code and the simulations beside the lesson.
Limestone is mostly calcium carbonate. Heated in a rotary kiln at about 1070 K to 1270 K, it gives quicklime:
The reaction is reversible. So the carbon dioxide is carried away as soon as it forms, and the change goes to completion.
Calcium oxide is a white solid with a very high melting point, about 2870 K. It is a basic oxide. It takes in water and carbon dioxide from the air. At high temperatures it combines with acidic oxides:
and
The first reaction removes sand as slag in a blast furnace.
Slaking. Water added to quicklime makes it hiss, steam and crumble to a powder. This is slaked lime, calcium hydroxide. A lot of heat is given out.
Quicklime slaked with sodium hydroxide solution gives soda lime, which takes in carbon dioxide and water.
Uses of quicklime. It is a raw material for cement and for slaked lime. It is used in purifying sugar, in making dyestuffs, and in the old method of making sodium hydroxide.
Calcium hydroxide dissolves only a little in water. Its clear solution is lime water, and a suspension of the solid in water is milk of lime.
Pass carbon dioxide into lime water, and it turns milky with calcium carbonate:
Keep passing the gas, and the milkiness goes. The carbonate turns into the soluble hydrogencarbonate:
This is how rain water with carbon dioxide dissolves limestone, and how temporary hardness forms.
Milk of lime takes up chlorine to give a mixture of calcium hypochlorite and calcium chloride, the active part of bleaching powder:
Notice that chlorine goes from 0 to in the chloride and to in the hypochlorite. It is both oxidised and reduced. This is disproportionation.
Uses of slaked lime. Mortar and whitewash, liming acid soils on farms, glass making, tanning leather, purifying sugar and making bleaching powder. It is a disinfectant too.
Mortar is slaked lime, sand and water. As it dries, the lime takes in carbon dioxide from the air and slowly turns back into calcium carbonate, which binds the sand.
Calcium carbonate is found as limestone, chalk and marble. In the laboratory it is made by passing carbon dioxide into slaked lime, or by adding sodium carbonate to calcium chloride:
It breaks up at about 1200 K. It fizzes with dilute acids and gives carbon dioxide:
Uses. Building stone (marble); a raw material for quicklime; mixed with magnesium carbonate as a flux in the extraction of iron; specially precipitated chalk in toothpaste, chewing gum and as a filler in cosmetics; an antacid.
Gypsum is calcium sulphate dihydrate, . Heated to about 393 K, it loses three quarters of its water and gives plaster of Paris, calcium sulphate hemihydrate:
Here is the same as written twice: half a water molecule for each calcium sulphate.
Heated more strongly, it loses all its water and becomes anhydrous calcium sulphate. This is called dead burnt plaster, because it no longer sets with water.
Setting. Mix plaster of Paris with water, and in five to fifteen minutes it becomes a hard mass of interlocking gypsum crystals. It expands a little as it sets, so it fills every corner of a mould.
Uses. Casts to hold broken bones, models of teeth in dentistry, statues and ornaments, moulds, and fire-resistant boards.
Portland cement is made by heating limestone with clay in a rotary kiln. The clay supplies silica, alumina and iron oxide. The product, called clinker, is ground with 2 to 3 % gypsum.
A typical composition by mass is:
For a good cement, the ratio of silica to alumina should be between 2.5 and 4. The ratio of lime to the total of silica, alumina and iron(III) oxide should be as close as possible to 2. With too much lime, the cement cracks while setting. With too little, it is weak.
The main compounds in clinker are tricalcium silicate (, about half), dicalcium silicate (, about a quarter) and tricalcium aluminate (, about a tenth). With water, these form hydrated silicates and aluminates that lock together into a hard mass. The gypsum slows down the setting, so that the cement can be worked before it hardens.
Some books, and the A-Level syllabus, use these compounds in a short form: for tricalcium silicate, and so on.
Set the temperature to 420 K. The mass falls by about 15.7 %. Raise it to 500 K, and the plaster becomes dead burnt.
The program works out the mass left at each step when gypsum is heated.
Try each one on your own first. If you are stuck, open a hint. Then check with Show the answer.
Every lesson is open to read. Enrolling also lets you:
Log in to join the discussion.
Loading…
This lesson is free to read. Enroll free to keep your place and take the tests.