Course 33.3Lesson 2 of 3
A torch beam shows up in a dusty room but not in clean air. A drop of milk under a microscope shows tiny bright specks that jiggle and never stop. This lesson explains these and the other properties of colloids, and why a pinch of salt makes a sol settle.
Try the code and the simulations beside the lesson.
Pass a narrow beam of light through a true solution in a dark room. Viewed from the side, the path of the beam cannot be seen. Pass it through a colloid, and the path shows up as a bright cone. This is the Tyndall effect.
Colloidal particles are large enough to scatter light sideways. Two conditions must hold:
A lyophilic sol, whose particles are close to the medium in refractive index, may show only a weak effect.
In the ultramicroscope, invented by Zsigmondy, a strong beam is focused on the sol and the microscope looks at right angles to it. Each particle appears as a bright speck. The particles themselves are not seen, only the light they scatter.
Small particles scatter blue light more than red. For particles much smaller than the wavelength, the scattered intensity is proportional to . This is why the sky looks blue.
Under an ultramicroscope the specks move all the time, in a zigzag path. This is Brownian motion, first seen by the botanist Robert Brown with pollen grains. It is caused by molecules of the medium striking a particle unequally from different sides. The motion stirs the sol and helps to keep the particles from settling.
A colloid has very few particles for its mass, because each particle is huge. So the colligative properties, such as the lowering of the freezing point and the osmotic pressure, are very small. Osmotic pressure is still large enough to measure, and it is used to find the molar mass of proteins and polymers.
The particles of a sol all carry the same charge, positive or negative. The medium carries an equal and opposite charge. The particles repel each other, and that keeps the sol stable.
Where the charge comes from. The most common cause is the preferential adsorption of ions. A particle adsorbs the ions that are part of its own crystal.
The ions held on the particle form a fixed layer. Ions of the opposite charge from the medium crowd around it in a diffuse layer, dense near the surface and thinner further out. Together they form the electrical double layer of Helmholtz.
When the particle moves, the fixed layer and part of the diffuse layer go with it. The potential at the plane where the rest of the medium slides past is the zeta potential, . A large zeta potential means strong repulsion and a stable sol.
Put a sol in a U-tube with an electrode in each arm, and apply a voltage. The particles move towards the electrode of opposite charge. This is electrophoresis. A negative sol moves to the anode, and a positive sol to the cathode. When the particles reach the electrode, they lose their charge and settle.
The speed divided by the electric field is the electrophoretic mobility, . For a particle much larger than the double layer, the Smoluchowski equation links it to the zeta potential:
where is the viscosity of the medium and its permittivity. For water at , and .
If the particles are held still by a membrane, the medium moves instead. This is electro-osmosis.
When the charge on the particles is removed, they come together and settle. This is coagulation (or flocculation). It can happen in four ways.
Not every ion is equally good at coagulating a sol. The Hardy-Schulze rule says that the higher the charge of the counter-ion, the greater its coagulating power.
The coagulation value of an electrolyte is the smallest concentration, in millimoles in each litre of the final mixture, that coagulates the sol in a set time, often two hours. The smaller the coagulation value, the greater the coagulating power.
Experiments often fit the Schulze-Hardy sixth power: the coagulation value varies as , where is the charge of the counter-ion. So ions of charge 1, 2 and 3 have coagulation values in the ratio .
Set . For the value is , and for only . A triply charged ion is 729 times more powerful.
A lyophilic sol added to a lyophobic sol can protect it from coagulation. The lyophilic particles form a layer around the lyophobic ones. Such a lyophilic colloid is a protective colloid. Gelatin protects the silver bromide of photographic films, and it stabilises ice cream.
The protective power is measured by the gold number, introduced by Zsigmondy. It is the mass in milligrams of the protective colloid that just protects of a standard red gold sol. The test adds of a sodium chloride solution, which would otherwise coagulate it. Coagulation shows as a change of colour from red to blue.
The smaller the gold number, the greater the protective power. Typical values are about 0.005 to 0.01 for gelatin and about 25 for potato starch.
The program works out three coagulation values from an experiment, and prints the ratios that the sixth power rule predicts.
Try each one on your own first. If you are stuck, open a hint. Then check with Show the answer.
Every lesson is open to read. Enrolling also lets you:
Log in to join the discussion.
Loading…
This lesson is free to read. Enroll free to keep your place and take the tests.