Maps, plans and ship courses all shrink the real world onto a page. You draw and read scale drawings, and change between a drawing length and a real length. You give directions as three-figure bearings measured clockwise from north, and you find the bearing of the way back.
about 25 min1 simulation1 practice question
Lesson 3 of 3Show all lessonsHide
Try the code and the simulations beside the lesson.
A map of your town fits on one page. A plan of a house fits on a sheet of paper. A drawing like this is a scale drawing: every length is the real length divided by the same number.
Scale
A scale can be written as a ratio or in words.
As a ratio:1:50000 means 1 unit on the map stands for 50000 of the same unit on the ground.
In words: "1cm represents 5m" means 1cm on the drawing stands for 5m in real life.
To change between the two, write the real length in the unit of the drawing. 5m=500cm, so "1cm to 5m" is the scale 1:500.
Drawing to real length: multiply by the scale number. A road measures 3.2cm on a map with scale 1:50000. The real length is 3.2×50000=160000cm. There are 100000cm in a kilometre, so the road is 1.6km.
Real to drawing length: divide. A room is 4.5m long. On a plan with scale 1:50 it is 450÷50=9cm long.
A scale drawing of a rectangular room with a door, with a scale bar. The room measures 9 centimetres by 6 centimetres on the drawing, and the scale is 1 to 50. A north arrow points up the page.
To make a scale drawing:
Choose a scale so the drawing fits the page.
Change every real length to a length on the drawing.
Draw with a ruler and a protractor. Use a ruler for every straight line.
Measure the length or angle you need, and change it back to real life.
Three-figure bearings
A bearing gives a direction. It is an angle measured clockwise from north, and it is always written with three figures. North is 000∘, east is 090∘, south is 180∘ and west is 270∘. A bearing of 25∘ is written 025∘.
Two points A and B. A north line is drawn at A and at B. The point B lies up and to the right of A. The angle from the north line at A clockwise to AB is marked 25 degrees. The angle from the north line at B clockwise to BA is marked 205 degrees.
Say "the bearing of B from A". Stand at A, face north, and turn clockwise until you face B. The angle you turn through is the bearing.
Words and bearings: "D is due east of C" means the bearing of D from C is 090∘. "Due south" is 180∘ and "due west" is 270∘.
The back bearing
If the bearing of B from A is 025∘, what is the bearing of A from B? Draw a north line at each point. The two north lines are parallel. The direction from B to A is the opposite direction, so it turns 180∘ more.
025∘+180∘=205∘.
The rule. The two bearings differ by 180∘. If the first bearing is less than 180∘, add 180∘. If it is 180∘ or more, subtract 180∘. A bearing of 310∘ has the back bearing 310∘−180∘=130∘.
A journey on a scale drawing
A ship sails 8km on a bearing of 050∘. Then it sails 6km on a bearing of 140∘. How far is it from the start?
Choose a scale.1cm represents 1km.
Draw the first leg. Draw north at the start. Use the protractor to draw 050∘ clockwise from north. Draw 8cm.
Draw the second leg. At the end of the first leg, draw a new north line. Measure 140∘ clockwise from north. Draw 6cm.
Join and measure. The line from the start to the end measures 10cm, so the ship is 10km from the start.
The turn between the legs is a right angle, since 140∘−50∘=90∘. So Pythagoras confirms it: 82+62=10.
Extended: areas on a scale drawing. Every length is divided by the scale number, so every area is divided by the scale number squared. On a map with scale 1:10000, each 1cm stands for 100m. So each 1cm2 on the map stands for 100×100=10000m2 on the ground.
Practise with new numbers
Try it in Python
The program turns a bearing and a distance into a point, finds the back bearing and measures the distance between two points.
Common mistakes
Measuring a bearing from the wrong line. Always measure clockwise from north.
Writing a bearing with two figures. Write 025∘, not 25∘.
Using the wrong direction for a back bearing. Add 180∘ if the bearing is below 180∘, and subtract it if not.
Not changing units. Write the real length in the unit of the drawing before using the scale.
Squaring the scale for a length. Only areas use the square of the scale.
Remember these
Scale 1:n: drawing length ×n = real length.
A bearing is measured clockwise from north, with three figures.
Back bearing: add 180∘ if below 180∘, subtract 180∘ if not.
Use a ruler for every straight line.
Areas change by the square of the scale.
Check yourself
Try each one on your own first. If you are stuck, open a hint. Then check with Show the answer.
A scale is 1:200. A wall is 6cm long on the drawing. How long is the real wall, in metres?
Write the bearing of a point due west of you, and of a point due south.
The bearing of Q from P is 320∘. What is the bearing of P from Q?
On a map, two villages are 7cm apart. The scale is 1:25000. How far apart are they in kilometres?
Extended. On a map with scale 1:1000, a pond has an area of 12cm2. What is its real area, in square metres?