Half of the food we eat depends on fertiliser, and much of the world's fertiliser starts with ammonia. This lesson is Extended. It gives the conditions of the Haber and the Contact processes and shows why a factory chooses them.
about 30 min1 simulation2 practice questions
Lesson 3 of 3Show all lessonsHide
Try the code and the simulations beside the lesson.
This lesson is Extended content. Industry cannot wait for a slow reaction, and cannot waste a lot of product. The conditions are a compromise between the rate and the position of equilibrium, with cost and safety.
The Haber process
The Haber process makes ammonia. The equation is:
N2(g)+3H2(g)⇌2NH3(g)
The nitrogen comes from the air.
The hydrogen comes from methane, the main gas in natural gas.
The typical conditions are 450 °C, a pressure of 20 000 kPa (200 atmospheres, or 200 atm), and an iron catalyst.
A flow chart of the Haber process. Nitrogen from air and hydrogen from methane go into a compressor at 20 000 kPa. The compressed gases go into a reactor with an iron catalyst at 450 degrees Celsius, where nitrogen plus 3 hydrogen is in equilibrium with 2 ammonia. The gas mixture then goes to a cooler where the ammonia becomes a liquid and is removed. An arrow returns the unreacted nitrogen and hydrogen to the compressor.
Why these conditions? The Haber process
We are told that the forward reaction is exothermic. There are 4 molecules of gas on the left and 2 on the right.
Temperature. A low temperature moves the position to the right, so there is more ammonia at equilibrium. But a low temperature gives a slow rate. A high temperature gives a faster rate but a smaller yield. 450∘C is a compromise, and the iron catalyst speeds up the reaction so that it reaches equilibrium quickly.
Pressure. A high pressure moves the position to the right, to the side with fewer molecules. It also makes the reaction faster. But very high pressures need thick, strong pipes and powerful pumps. That is expensive and dangerous, because a leak at a very high pressure can cause an explosion. So 20000 kPa is a compromise.
Removing the ammonia. The hot gas leaving the reactor is cooled. The ammonia becomes a liquid and is taken away. The nitrogen and hydrogen that did not react go back to the reactor, so none of them is wasted. Only part of the gas changes to ammonia on each pass.
The Contact process
The Contact process makes sulfur trioxide, the step before sulfuric acid.
2SO2(g)+O2(g)⇌2SO3(g)
The sulfur dioxide comes from burning sulfur, S+O2→SO2, or from roasting sulfide ores in air.
The oxygen comes from the air.
The typical conditions are 450 °C, a pressure of 200 kPa (2 atm) and a vanadium(V) oxide catalyst.
Why these conditions? The Contact process
The forward reaction is exothermic. There are 3 molecules of gas on the left and 2 on the right.
Temperature. As in the Haber process, a lower temperature gives a better yield but a slow rate. 450∘C with a catalyst is a compromise.
Pressure. A higher pressure would move the position to the right. But at only 200 kPa the yield is already very high, around 95 percent or more. The extra yield is not worth the cost of strong equipment and the danger of the hot, corrosive gases at a high pressure. So the plant uses almost normal pressure.
Comparing the two
Both processes use 450 °C and a catalyst, because both have an exothermic forward reaction.
The Haber process uses a very high pressure, because the yield at normal pressure is low. The Contact process does not need it.
Both use the air for one of the reactants and recycle what did not react, or pass the gas over more catalyst.
Practise with new numbers
Try it in Python
The program shows how the share of gas changed to ammonia grows with the number of passes.
Common mistakes
Mixing up the two processes. Haber: nitrogen, hydrogen, iron, 20 000 kPa. Contact: sulfur dioxide, oxygen, vanadium(V) oxide, 200 kPa.
Giving only the best yield as the reason. The conditions are also chosen for the rate, the cost and the safety.
Saying that a catalyst raises the yield. The catalyst speeds up the reaction. It does not move the position.
Saying that the pressure is as high as possible. Equipment cost and danger set a limit.
Forgetting the recycling. The gases that did not react are used again.
Remember these
Haber: N2+3H2⇌2NH3. Nitrogen from air, hydrogen from methane. 450 °C, 20 000 kPa (200 atm), iron.
Contact: 2SO2+O2⇌2SO3. Sulfur dioxide from burning sulfur or roasting sulfide ores, oxygen from air. 450 °C, 200 kPa (2 atm), vanadium(V) oxide.
A low temperature gives a better yield but a slow rate. The catalyst makes a moderate temperature work.
A high pressure favours the side with fewer molecules, but costs more and is more dangerous.
Check yourself
Try each one on your own first. If you are stuck, open a hint. Then check with Show the answer.
Extended: where do the nitrogen and the hydrogen of the Haber process come from?
Extended: a student says that the Haber process uses 450 °C, 200 kPa and a vanadium(V) oxide catalyst. Correct her.
Extended: why is a temperature much lower than 450∘C not used in the Haber process?
Extended: why does the Contact process not need a pressure of 20000 kPa?
Extended: what is the catalyst in the Contact process?
References
Cambridge IGCSE Chemistry 0620 syllabus for 2026 to 2028, section 6.3 (Reversible reactions and equilibrium), Supplement 5 to 11.