How a catalyst works: homogeneous and heterogeneous catalysis
A mixture of hydrogen and oxygen can sit for years without reacting. Add a speck of platinum, and it reacts at once. The platinum is still there at the end. This lesson explains what a catalyst changes, what it cannot change, and how a solid surface speeds up a reaction between gases.
about 25 min1 simulation1 practice question
Lesson 1 of 3Show all lessonsHide
Try the code and the simulations beside the lesson.
What a catalyst is
A catalyst is a substance that makes a reaction faster and is left chemically unchanged at the end. The process is catalysis. A small amount of catalyst can serve a very large amount of reactant.
A catalyst works by offering a new path for the reaction, with a lower activation energy. More molecules have enough energy to cross the lower barrier, so the reaction is faster.
An energy profile of a reaction: energy on the vertical axis against the progress of the reaction. The products lie below the reactants, so the reaction is exothermic. A tall blue curve, the path without a catalyst, rises to a high peak. A lower orange curve, the path with a catalyst, rises to a lower peak. The activation energy of each path is marked with an arrow from the reactants to its peak. The enthalpy change, from reactants to products, is the same for both paths.
By the Arrhenius equation, k=Ae−Ea/RT. If the catalyst lowers Ea by ΔE and leaves A unchanged, the rate constant grows by a factor
kkcat=eΔE/RT
For example, a drop from 75kJ/mol to 50kJ/mol at 298K makes the reaction about 24 000 times faster.
What a catalyst does not change
It does not change ΔH or ΔG. The reactants and products are the same, so the energy change is the same.
It does not change the equilibrium constant. The forward and backward barriers both fall by the same ΔE. Both rate constants grow by the same factor, so K=kf/kb stays the same. The catalyst only helps the mixture reach equilibrium sooner.
It cannot start a reaction that is not spontaneous. A reaction with ΔG>0 stays non-spontaneous.
It is specific. A catalyst usually works for one reaction or one type of reaction.
Keep ΔE=25kJ/mol and move the temperature from 300 K to 1000 K. The ratio falls from about 104 to about 20. A catalyst gains most at a low temperature, which is why industry uses one: the reaction can run cool, where the equilibrium of an exothermic reaction is more favourable.
Homogeneous catalysis
In homogeneous catalysis the catalyst is in the same phase as the reactants, usually all gases or all in one solution.
Nitrogen monoxide in the lead chamber process.2SO2(g)+O2(g)→2SO3(g) is catalysed by NO(g). The gas carries oxygen: 2NO+O2→2NO2, then NO2+SO2→SO3+NO.
Acids in hydrolysis. The hydrolysis of methyl acetate, CH3COOCH3+H2O→CH3COOH+CH3OH, is catalysed by H+ ions in solution. So is the hydrolysis of sucrose into glucose and fructose.
Iron ions with peroxodisulphate. In A-Level Chemistry, iron(II) or iron(III) ions catalyse the slow reaction between peroxodisulphate and iodide ions. Both reactants are negative ions that repel each other. Iron ions react with each in turn, changing between the two oxidation states.
A homogeneous catalyst often works by forming an intermediate with a reactant, which then reacts further and gives the catalyst back.
Heterogeneous catalysis
In heterogeneous catalysis the catalyst is in a different phase, usually a solid with gases or liquids around it.
The Haber process.N2(g)+3H2(g)→2NH3(g) on iron, Fe(s).
The Ostwald process.4NH3(g)+5O2(g)→4NO(g)+6H2O(g) on a platinum and rhodium gauze.
The contact process.2SO2(g)+O2(g)→2SO3(g) on vanadium(V) oxide, V2O5. The older NCERT book shows platinum, which was used first.
Hydrogenation of vegetable oils on finely divided nickel, to make solid fats.
Catalytic converters in cars, where platinum, palladium and rhodium turn carbon monoxide, unburnt fuel and nitrogen oxides into carbon dioxide, water and nitrogen.
The adsorption theory: five steps on a surface
How does a surface speed up a reaction? The reactants are adsorbed on the catalyst, usually by chemisorption, and react there.
Five steps of a reaction on a catalyst surface, drawn as five boxes joined by arrows. 1: the reactant molecules diffuse to the surface. 2: they are adsorbed on the surface. 3: they react on the surface, through an activated complex. 4: the product molecules are desorbed. 5: the products diffuse away, and the sites are free again.
Diffusion of the reactants to the surface.
Adsorption of the reactants. Bonds within the reactant molecules are weakened, and the molecules are held close together.
Reaction on the surface, through an activated complex.
Desorption of the products, which frees the sites.
Diffusion of the products away from the surface.
A good catalyst holds the reactants firmly enough to weaken their bonds, but lets the products go. Fine powders work best, because they have more surface.
The rate on a surface: the Langmuir-Hinshelwood idea
Suppose one gas, A, decomposes on a surface. The rate is proportional to the fraction of sites that hold A, so by the Langmuir isotherm
r=kθ=1+KPkKP
At low pressure, KP≪1 and r≈kKP: the reaction is first order in A.
At high pressure, KP≫1 and r≈k: the surface is full, and the reaction is zero order.
This explains a famous result. The decomposition of ammonia on hot tungsten, 2NH3→N2+3H2, is zero order at moderate pressures: the rate does not depend on the pressure of ammonia. The decomposition of phosphine on tungsten is first order at low pressure. In between, the apparent order is 1+KP1.
Practise with new numbers
Try it in Python
The program works out how many times faster a reaction goes at three temperatures when a catalyst lowers its activation energy.
Common mistakes
Saying a catalyst shifts the equilibrium. It speeds both directions by the same factor.
Saying a catalyst is not used up, so it takes no part. It takes part, through intermediates or adsorbed species, and is given back.
Forgetting that a heterogeneous reaction can be zero order. When the surface is full, the rate does not depend on the pressure.
Leaving ΔE in kilojoules when R is in joules.
Remember these
kkcat=eΔE/RT, the same factor for the forward and backward reactions.
Homogeneous: same phase. Heterogeneous: different phases, usually a solid with gases.
Five steps: diffusion, adsorption, reaction, desorption, diffusion.
On a surface: r=1+KPkKP, first order at low pressure, zero order at high pressure.