HelpContactFor teachers and institutes
>_StemPy Lab
Mock TestsClasses

>_StemPy Lab

Learn. Solve. Code the solutions. Test yourself.

Live examsFree mock exams, timed and rankedEveryone starts together, and your score and rank come the moment it ends.See the exams →

Learn

  • Physics
  • Chemistry
  • Mathematics
  • Biology
  • Python Programming
  • Statistics & Data Science
  • Classes
  • Groups

Practice

  • Problems
  • Quizzes
  • Mock Tests
  • Prepare for an Exam
  • Question Sets
  • Exams
  • Certificates
  • Python Labs
  • AI Practice Generator
  • Student-Created Tests

Community

  • Discussions
  • Resources
  • Notes
  • Glossary
  • Blog

Account

  • Log in
© 2026 senLearn. All rights reserved.HelpFor SchoolsAboutContactPrivacy PolicyTerms of UseRefund Policy
Populations and Their Limits
  1. 1Populations, communities and ecosystems
  2. 2The sigmoid growth curve
  3. 3Limiting factors and the phases of growth
  1. Biology
  2. /Populations and Their Limits
  3. /Limiting factors and the phases of growth

Course 13.2·Lesson 3 of 3

Limiting factors and the phases of growth

Each phase of the growth curve has a reason, and the reasons are limiting factors. This lesson explains the lag, exponential, stationary and death phases in terms of food, space, waste and the balance of births and deaths. It then uses a model to show why a population levels off.

about 25 min1 simulation1 practice question
Lesson 3 of 3Show all lessonsHide
Populations and Their Limits
  1. 1Populations, communities and ecosystems
  2. 2The sigmoid growth curve
  3. 3Limiting factors and the phases of growth

Try the code and the simulations beside the lesson.

Why does the curve bend?

Why does a population not go on doubling for ever? If one bacterium doubled every 20 minutes, in a day there would be more bacteria than there are grains of sand on Earth. The answer is limiting factors. A limiting factor is something that is in short supply, or too much, so that it stops a population from growing any further. This lesson is Extended content.

The reason for each phase

The same S-shaped growth curve with four call-out notes. Lag phase: cells adjust to the new food and make enzymes, and few cells divide. Exponential phase: plenty of food and space, little waste, so births are much greater than deaths. Stationary phase: food runs short and wastes build up, so births equal deaths. Death phase: food is used up and wastes are poisonous, so deaths are greater than births.
  • Lag phase. The cells have just been put into new broth. They take time to adjust, and they make the enzymes they need for the new food. Few cells divide, so the number rises slowly.
  • Exponential phase. There is plenty of food and space, and few waste products. Nothing limits growth. Many cells divide, and few die, so births are much greater than deaths. The more cells there are, the more divide, so growth speeds up.
  • Stationary phase. Now limiting factors act. Food is running short, waste products are building up, and the cells compete for what is left. The number of cells that divide equals the number that die, so births equal deaths.
  • Death phase. The food is used up, and the waste products are now poisonous. More cells die than are made, so deaths are greater than births and the number falls.

For yeast in a sugar solution, one waste product is ethanol. When there is too much, it kills the yeast.

Wild populations

The same ideas work for animals in the wild. A herd on a grassland grows while there is plenty of grass. As the herd grows, the grass becomes scarce, and competition, hunger and disease raise the number of deaths. Predators also take prey. A population levels off where births equal deaths, and this level depends on the food and space of the habitat.

A model of the levelling off

The simulation below uses a simple model. The births per animal fall as the population nears the level that the food can support. The deaths per animal stay the same. The model is not part of the syllabus. It shows births and deaths balancing.

You should find that a larger food limit moves the crossing point to the right. More food supports a bigger stationary population. A higher death rate moves it to the left.

Try it in Python

The program follows the model for thirty steps.

Read it first. At which step do you expect births and deaths to be equal? Then run it.

1. Change food_limit = 600 to 1000. Where does the population settle now?

2. Change death_rate = 0.2 to 0.4. Does the population settle higher or lower?

Practise with new numbers

Common mistakes

  • Saying that the exponential phase has no deaths. There are deaths, but many more births.
  • Writing that the stationary phase has no births. Births go on. They are equal to the deaths.
  • Giving a reason for a phase without a limiting factor. In the stationary and death phases, name the food, waste or space.
  • Mixing up the reasons. Cells adjusting and making enzymes belongs to the lag phase.

Remember these

  • A limiting factor is a factor that is in short supply, or too much, so that it stops further growth.
  • Lag: cells adjust. Exponential: plenty of food, births greater than deaths. Stationary: limiting factors, births equal deaths. Death: food used up and poisonous waste, deaths greater than births.

Where next

The Class 11 and 12 chapter on organisms and populations gives the equations of exponential and logistic growth. Here the curve is read and explained in words.

Check yourself

Try each one on your own first. If you are stuck, open a hint. Then check with Show the answer.

  1. Why is growth slow in the lag phase?
  1. Why do the cells multiply fast in the exponential phase?
  1. What is true of births and deaths in the stationary phase?
  1. Give two reasons why the cells die in the death phase.
  1. Give one limiting factor for a population of deer in a forest.

References

  • Cambridge IGCSE Biology 0610, syllabus for examination in 2026, 2027 and 2028, section 19.4, point 7.
  • OpenStax Biology 2e (2018), chapter 45, Population and Community Ecology, sections 45.3 and 45.4.

Enroll free in Populations and Their Limits

Every lesson is open to read. Enrolling also lets you:

  • Mark lessons done and carry on where you stopped.
  • Take the tests of this lesson and its course.
  • Count the course towards the certificate for its chapter.
No payment. You can leave at any time.

Problems (2)

Yeast cells are put into a flask of sugar solution and counted over a few days…Medium · High School (9–10) · by StemPy Lab
The table shows the number of cells made and the number that die in each hour, at four stages of a…Hard · High School (9–10) · by StemPy Lab

Python Labs (1)

That was the last lessonBack to the course: take the test
← Populations and Their Limits
← The sigmoid growth curveNext →

Discussion (0)

Log in to join the discussion.

Loading…

1 Python program
5 questions to check yourself

This lesson is free to read. Enroll free to keep your place and take the tests.

A model of levelling offPython Lab · by StemPy Lab

Question Sets (1)

Populations: Review Questions10 questions · by StemPy Lab

Notes (1)

Populations: Quick RevisionNote · by StemPy Lab